Search: Posts Made By: kcxj
Showing results 1 to 25 of 200
Search took 0.04 seconds.
Replies: 8
Views: 1,164
Posted By kcxj

The last “keypad” is a Honeywell lynx all in one...

The last “keypad” is a Honeywell lynx all in one panel.

It is pretty common in some areas to run the alarm wires in to a structured media cabinet like you have, Some SMC even have an alarm panel...
Replies: 5
Views: 628
Posted By kcxj

From keypad: enter 984 CMD, choose test, then...

From keypad: enter 984 CMD, choose test, then path 1.

what happens?
Replies: 5
Views: 628
Posted By kcxj

The latest firmware is version 212 and that...

The latest firmware is version 212 and that firmware came out in 2013. I doubt your issues are firmware related, though. What is your communication method? I’m assuming digital dialer (serial 3).
Replies: 5
Views: 2,315
Posted By kcxj

The Securecom cameras use a VPN connection to...

The Securecom cameras use a VPN connection to talk to the Securecom servers. There is no default login, the login and password is assigned during activation.
Replies: 3
Views: 594
Posted By kcxj

As long as your DMP panel is not locked out,...

As long as your DMP panel is not locked out, there is no reason to replace. Check out Alarm Relay, they are familiar with DMP.
Replies: 11
Views: 1,556
Posted By kcxj

I would check out Alarm Relay. They can monitor...

I would check out Alarm Relay. They can monitor for $8.95 /month and they have a lot of experience with DMP. Good company and easy to cancel if needed.
Replies: 3
Views: 2,917
Posted By kcxj

DMP Cellular communicators are not locked, so...

DMP Cellular communicators are not locked, so someone could potentially swap in a new SIM card. However, that unit being soldered on board is for sure a 2g communicator which has been shut down in...
Replies: 10
Views: 923
Posted By kcxj

Make sure auto stay is turned off. Is that field...

Make sure auto stay is turned off. Is that field 84?
Replies: 3
Views: 563
Posted By kcxj

You can do this with the System Sensor RRS-MOD...

You can do this with the System Sensor RRS-MOD and System Sensor 2WTA-B detectors. You will need to get approval from the local AHJ, though.

http://library.ademconet.com/MWT/fs2/4/6036.pdf
Replies: 8
Views: 730
Posted By kcxj

System sensor piezo alert, likely tied to a duct...

System sensor piezo alert, likely tied to a duct detector. I believe what looks like a black dot is a red led, which if you were to look closely, likely states alarm underneath.
Replies: 7
Views: 770
Posted By kcxj

Many moons ago when I worked for ADT, the SOP for...

Many moons ago when I worked for ADT, the SOP for all undefined signals were to treat as a panic alarm. Although, this may have changed, you will likely need a service call to define the zone--ADT...
Replies: 8
Views: 1,453
Posted By kcxj

The vista panel needs a momentary short to arm...

The vista panel needs a momentary short to arm away. If a short is applied and maintained for ~ 10 seconds, the panel with arm stay.
Replies: 11
Views: 1,056
Posted By kcxj

You likely caused a trouble condition when you...

You likely caused a trouble condition when you removed the original detector. Try entering your code+1 twice in a row.
Replies: 4
Views: 687
Posted By kcxj

Perfect application for the ReBore-zit from labor...

Perfect application for the ReBore-zit from labor saving devices

Labor Saving Devices (http://www.lsdinc.com/drilling-tools.php)
Replies: 16
Views: 1,345
Posted By kcxj

Alarm Relay never charged me extra for Network. ...

Alarm Relay never charged me extra for Network. Cell I get wholesale from the source.
Replies: 16
Views: 1,345
Posted By kcxj

I agree to a point that you usually get what you...

I agree to a point that you usually get what you pay for. However, the large national companies have done a good job of projecting that $30-$40/month is what you should pay for monitoring. The fact...
Replies: 16
Views: 1,345
Posted By kcxj

I have had good luck with Alarm Relay.

I have had good luck with Alarm Relay.
Replies: 11
Views: 2,782
Posted By kcxj

Total Connect can do it, although it is a bit...

Total Connect can do it, although it is a bit clunky. By default Total Connect only displays partition 1. So, you would need to choose keypad from the arming screen and use the keypad emulator to...
Replies: 11
Views: 2,782
Posted By kcxj

The best application I have seen to utilize...

The best application I have seen to utilize multiple areas or partitions is the DMP virtual keypad.
Replies: 11
Views: 2,782
Posted By kcxj

ADT pulse is rebranded iControl. If you had the...

ADT pulse is rebranded iControl. If you had the equivalent of AlarmNet Total connect, you could jump partitions with the Emulated keypad.
Replies: 10
Views: 4,795
Posted By kcxj

I am assuming that you powered up the keypad,...

I am assuming that you powered up the keypad, pressed the 1 and 3 buttons together for a few seconds and entered the device address of "00". All Honeywell keypads are shipped from the factory as...
Replies: 3
Views: 612
Posted By kcxj

That should work. Just make sure you have a...

That should work. Just make sure you have a spare zone for the key switch.
Replies: 3
Views: 612
Posted By kcxj

I have done this before by wiring an output off...

I have done this before by wiring an output off the access control panel that momentarily shorts a key switch on the burglar alarm system. The tricky part is preventing the access system from...
Replies: 9
Views: 1,070
Posted By kcxj

You are booting into the address setting menu. ...

You are booting into the address setting menu. The control panel upstairs is a DSC unit that is not compatible with the Ademco keypad. Is it possible that the circuit board inside the upstairs...
Replies: 22
Views: 6,948
Posted By kcxj

Around 2012 Ademco changed the resistors for the...

Around 2012 Ademco changed the resistors for the 4219/4229 expanders from 1k to 2k to match the modern panels. I would suspect your old expansions zones have 1k resistors and your expander is...
Showing results 1 to 25 of 200
 


 
Forum Jump