Search: Posts Made By: athenshome
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 27
Views: 45,992
Posted By athenshome

Testing with a multimeter. Did try jumping with...

Testing with a multimeter. Did try jumping with no success as well
Replies: 27
Views: 45,992
Posted By athenshome

It actually was not only the kill wire shorting. ...

It actually was not only the kill wire shorting. I also found an additional wire in the ignition harness that was shorting (orange wire). Swapped it out and it no longer blows the fuse, so good to...
Replies: 27
Views: 45,992
Posted By athenshome

Sorry for my delayed response to this thread. I...

Sorry for my delayed response to this thread. I did find where the short was and it was in the kill wire. It was shorting out somewhere right after the 6-plug harness, so I'm just running new wires...
Replies: 27
Views: 45,992
Posted By athenshome

Here's what I've found so far... The red wire...

Here's what I've found so far... The red wire going from the ignition switch (terminal B) to the fuse holder was bad. I just replaced this wire with a new one and still the same thing happened, it...
Replies: 27
Views: 45,992
Posted By athenshome

Husqvarna mower blowing fuses and not running

Ok this is driving me nuts!! I have a Husqvarna YTH1542 riding mower. It has been running fine without problems, has new battery and good starter and solenoid. A friend of mine was using it the...
08-06-12, 06:21 AM
Replies: 7
Views: 4,684
Posted By athenshome

The gap is between the sheetrock and the prehung...

The gap is between the sheetrock and the prehung frame. I've attached a few pictures of my door. You'll see at the bottoms where the frame doesn't match up to the house frame. It is not this way...
08-05-12, 08:36 PM
Replies: 7
Views: 4,684
Posted By athenshome

No, the "door" itself is fine and swings/closes...

No, the "door" itself is fine and swings/closes fine. My issue is with the prehung frame. Basically, there will be a 1/8-1/4" gap in the molding when I put it back on.
08-05-12, 08:00 PM
Replies: 7
Views: 4,684
Posted By athenshome

Problems Hanging Exterior Door

I am installing a new prehung door in my kitchen and got to the end and had a problem I cannot figure out! I got the door set in place without problem, level at all angles. But when I came back...
07-02-10, 09:38 PM
Replies: 1
Views: 881
Posted By athenshome

Repairing Grout on Tile Floor??

I have a house that was built in 1968 on a crawl space. We recently had tile flooring installed in our den over the wood subfloor (backer-board between the subfloor and thinset). I noticed after...
Replies: 1
Views: 4,527
Posted By athenshome

Weedeater Head won't Turn?? Engine Runs

I have a Troy Built weedeater (straight bar) that is no more than 1 year old. I was going to use it the other day when I noticed the problem.

The engine will crank and run as it should, but when...
04-30-09, 04:02 PM
Replies: 1
Views: 1,441
Posted By athenshome

Moving a Load-bearing Wall

I have a bathroom on the second level of my house that is very narrow. I am thinking about expanding the load-bearing wall. where the vanity is currently up against, out approx. 3' to obtain more...
04-27-09, 12:56 PM
Replies: 1
Views: 1,036
Posted By athenshome

Re-opening an Enclosed Garage

I recently purchased a house that once had a garage/carport area that was walled off and finished into a room. The previous owners did not raise the floor to grade level, just simply framed a wall...
04-24-09, 10:08 AM
Replies: 1
Views: 1,048
Posted By athenshome

Moving/Expanding a Load-Bearing Wall

I have a bathroom on the second level of my house that is very narrow. I am thinking about expanding the load-bearing wall. where the vanity is currently up against, out approx. 3' to obtain more...
Showing results 1 to 13 of 13


 
Forum Jump