Search: Posts Made By: Bilhar381
Showing results 1 to 25 of 68
Search took 0.01 seconds.
11-23-18, 12:30 AM
Replies: 10
Views: 2,042
Posted By Bilhar381

I reinstalled my ICM2808 control board, and...

I reinstalled my ICM2808 control board, and everything is working now. Thanks a bunch for all the help and tips.
11-20-18, 07:53 AM
Replies: 10
Views: 2,042
Posted By Bilhar381

Do I check the Xformer at the 120 connection, ...

Do I check the Xformer at the 120 connection, and then the other upper side for 24v
11-20-18, 05:15 AM
Replies: 10
Views: 2,042
Posted By Bilhar381

How do you check the Transformer -

How do you check the Transformer -
11-18-18, 05:08 AM
Replies: 10
Views: 2,042
Posted By Bilhar381

Thanks for the tip, both of you- I will check...

Thanks for the tip, both of you- I will check out the Transformer this morning. I did install a Fuse Link to prevent damage when I installed the new Transformer, some time in the past. But I will...
11-17-18, 11:17 AM
Replies: 11
Views: 2,988
Posted By Bilhar381

The new board was not the same as the old one, ...

The new board was not the same as the old one, mounting holes did not line up, I am 81 years old and got tired of trying. I don't know where to start.
11-17-18, 08:37 AM
Replies: 10
Views: 2,042
Posted By Bilhar381

No Power at the Control Board York Furnace

p3urd14n09501-Original Control Board White Rogers 50A50-241 , I replaced this board with an ICM2808-However I did not install it right, and it shorted against the meatal frame. Blew fuses.
The...
11-17-18, 06:46 AM
Replies: 11
Views: 2,988
Posted By Bilhar381

Same Problem on a York

Sorry I can,t find where to start a new Thread- I installed a new Control Board several months ago-it worked fine but I didn't have it mounted correctly, it started to blow fuse's. Acouple of days...
01-05-18, 12:07 PM
Replies: 6
Views: 1,984
Posted By Bilhar381

If you don't know where the filter is, how have...

If you don't know where the filter is, how have you changed it, how old is your furnace-
01-05-18, 10:45 AM
Replies: 1
Views: 1,093
Posted By Bilhar381

Furnace short problem-York P3urd14n09501

My furnace has been blowing fuse's, today I discoverd that if I do not connect the Metal Control Board Housing to the upper part of furnace, (where the burners are) it will run and not blow...
01-01-18, 05:30 AM
Replies: 3
Views: 948
Posted By Bilhar381

How did you solve this problem

I have a similiar problem with a York furnace, how was you problem solved.
11-06-17, 02:51 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

Progress: I have heat now most of the time-The...

Progress: I have heat now most of the time-The diagnostic lite was blinking 3 red flashes, which is a Pressure switch problem, I found I had a new pressure switch , so I installed it, and that...
11-05-17, 04:46 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

I changed the control board to ICM2808, and that...

I changed the control board to ICM2808, and that CIRC line was not indicated on the new board, so I connected it to the 4th terminal from the right and it goes to the Blower motor. Tell me if this...
11-04-17, 12:49 PM
Replies: 19
Views: 1,272
Posted By Bilhar381

Jesus what is next, after running for awhile this...

Jesus what is next, after running for awhile this morning, the dam Furnace blower will not turn on, not on auto or on fan -someone help me because I am out of ideas.
11-04-17, 03:15 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

Thanks for that info PJmax, I will look at the...

Thanks for that info PJmax, I will look at the T-stat wire-I wired the new control board same as the old board, and I am having the same problem .
11-03-17, 01:00 PM
Replies: 19
Views: 1,272
Posted By Bilhar381

Well I installed the new Limit switch , and no...

Well I installed the new Limit switch , and no luck, the dam thing will turn the furnace on, but it won't shut off the fan, it continues to blow cold air after the burner is shut off, it runs on...
11-02-17, 04:22 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

Update-I installed a new Control Board, had one...

Update-I installed a new Control Board, had one little problem, 9 blinks on the Diagnostic lite, Polarity, I also installed a new Transformer, so I switched the 120v lines, cured the problem- ...
10-27-17, 07:15 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

No everthing is not working, no power to ventor...

No everthing is not working, no power to ventor motor-
10-26-17, 04:30 PM
Replies: 19
Views: 1,272
Posted By Bilhar381

Maybe its reading 27 not 21, will check it again...

Maybe its reading 27 not 21, will check it again -later though, I am too tired right now-
10-26-17, 07:13 AM
Replies: 19
Views: 1,272
Posted By Bilhar381

UPDate- I have power to the Board and I get one...

UPDate- I have power to the Board and I get one Red lite at the start- I checked the Fuse I installed and it was blown, changed it, and now get one blink on the Diagnostic lite. Checking the...
10-25-17, 01:00 PM
Replies: 19
Views: 1,272
Posted By Bilhar381

How do I check the transformer, I did replace it...

How do I check the transformer, I did replace it not long ago-Would that put out the Diagnostic lite.
10-25-17, 12:04 PM
Replies: 19
Views: 1,272
Posted By Bilhar381

York P3URD14N09501-no diagnostic light

I have lost my diagnostic red lite on my furnace, in addition I have no power to the Ventor motor and of course it won't lite and run. I am getting ready to order a new Control Board-There is power...
02-02-17, 10:30 AM
Replies: 1
Views: 542
Posted By Bilhar381

Control Board York P3URD14N09501

My Control Board no longer blinks an Error code, the only time it lights up is when I turn the Furnace back on from a shut off. It then blinks one time. My Furnace is about 18 years old, so I don't...
02-02-17, 09:48 AM
Replies: 5
Views: 915
Posted By Bilhar381

As I stated in my previous post, I already...

As I stated in my previous post, I already installed the new Burners, they were rusted on the edge, My Gas supplier is a Propane company and they are located some distance away, they will charge me...
02-02-17, 09:44 AM
Replies: 5
Views: 915
Posted By Bilhar381

Multiple Problems

A short time ago, I received my new Burners, I installed them and now the furnace will ignite. So that problem is solved.

Now I suspect my Control Board is gone bad, it does not blink a code...
02-02-17, 03:30 AM
Replies: 5
Views: 915
Posted By Bilhar381

I am not sure what you mean by Crossovers, if...

I am not sure what you mean by Crossovers, if you mean the little grove on the side of the burner, then yes I cleaned them, wire brush and scraper. I see no obstruction on any thing else.
Showing results 1 to 25 of 68
 


 
Forum Jump