Search: Posts Made By: mailman2
Showing results 1 to 25 of 74
Search took 0.01 seconds.
Replies: 1
Views: 1,165
Posted By mailman2

troy built snowblower

troy bilt model 31AE6GQ3711 will not go out of gear. the friction plate is not touching. Pulled axle and when I released the top gear and slid it away, the wheels moved freely. Then when I slowly...
Replies: 3
Views: 9,927
Posted By mailman2

can anyone help, just tell me where the fuel...

can anyone help, just tell me where the fuel lines go
Replies: 3
Views: 9,927
Posted By mailman2

troybilt tb20cs fuel line diagram

does anyone know why my primer bulb does not fill when push in? Need diagram for fuel tank to primer and carb
Replies: 7
Views: 1,539
Posted By mailman2

I have the manual and I all ready located the...

I have the manual and I all ready located the part. Thank you
Replies: 7
Views: 1,539
Posted By mailman2

I just noticed that when the friction wheel is...

I just noticed that when the friction wheel is hitting the disk, I can still turn the tires and watching the chain sprocket still turn. Is there a key that goes under the small chain sprocket?
Replies: 7
Views: 1,539
Posted By mailman2

Is there a keyway on the drive axle that may have...

Is there a keyway on the drive axle that may have fallen out?
Replies: 7
Views: 1,539
Posted By mailman2

How come the wheels are free? Even when I press...

How come the wheels are free? Even when I press the handle
Replies: 7
Views: 1,539
Posted By mailman2

What I was trying to say is, before I changed the...

What I was trying to say is, before I changed the disk, the wheels were free when I pushed it, and when I pressed the traction lever, the wheels are still free. Not the auger
Replies: 7
Views: 1,539
Posted By mailman2

Ariens snowblower

Replaced the friction disk on my model 932100 824. My problem is, When I put the roll pins back in, some how they didn't line up right. Because when I push the blower and then depress the traction...
Replies: 18
Views: 3,517
Posted By mailman2

it says I can't post attachments

it says I can't post attachments
Replies: 18
Views: 3,517
Posted By mailman2

Got it running and found out why it wouldn't go...

Got it running and found out why it wouldn't go slow and fast, the throttle cable wasn't adjusted right. It now goes slow and fast, but with hesitation and does not run smoothly. under load with the...
Replies: 18
Views: 3,517
Posted By mailman2

Thanks . What hole? And how can you post...

Thanks . What hole? And how can you post pictures on here?
Replies: 18
Views: 3,517
Posted By mailman2

Tecumseh model TVM220 SPEC 157291K DOM...

Tecumseh model TVM220
SPEC 157291K
DOM 03107CB0027
It's on a Snapper rider mower
Replies: 18
Views: 3,517
Posted By mailman2

how do I know what spring to get? When I start...

how do I know what spring to get? When I start it with choke on, it starts to sputter, then when I move the throttle to high speed it just keeps on searching, then when I move it to slow, there is...
Replies: 18
Views: 3,517
Posted By mailman2

Started up but still surging. Has only one...

Started up but still surging. Has only one speed. When I move the throttle , nothing happens. What do you think it is, it is driving me to drink
Replies: 18
Views: 3,517
Posted By mailman2

took the carb off and cleaned the 3 holes, they...

took the carb off and cleaned the 3 holes, they were clean. Could the gasket be bad, it had a tear in it. May I had a leak in the gasket
Replies: 18
Views: 3,517
Posted By mailman2

I'll try that now. Can I just take the bolt from...

I'll try that now. Can I just take the bolt from the bottom of the carb, without taking the carb. off?
Replies: 18
Views: 3,517
Posted By mailman2

cleaned the carb and all looks good. I did take...

cleaned the carb and all looks good. I did take the spring off the gov. and may have stretched it. Could this cause the hard starting and surging
Replies: 18
Views: 3,517
Posted By mailman2

TVM 220 8 hp tecumseh

How do you set the governor on this engine, it surges and doesn't get up to full throttle
Replies: 7
Views: 1,399
Posted By mailman2

No problem..... Why did I come here anyhow? I...

No problem..... Why did I come here anyhow? I forgot
Replies: 7
Views: 1,399
Posted By mailman2

Thanks, i'll try that later today

Thanks, i'll try that later today
Replies: 7
Views: 1,399
Posted By mailman2

wiring harness, it is short by 2 feet

wiring harness, it is short by 2 feet
Replies: 7
Views: 1,399
Posted By mailman2

power winch

Just got a new trailer and I need another 2 feet of wire for my power winch. What size wire should I get and where do I splice it to?[battery side or cut some place in the middle]
Replies: 4
Views: 1,800
Posted By mailman2

Thank you very much, didn't want to get wrong...

Thank you very much, didn't want to get wrong ones.
Replies: 4
Views: 1,800
Posted By mailman2

So, the manual numbers are wrong?

So, the manual numbers are wrong?
Showing results 1 to 25 of 74
 


 
Forum Jump