Search: Posts Made By: longtimealaskan
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Replies: 4
Views: 567
Posted By longtimealaskan

I think I have it. 529 refers to the model...

I think I have it. 529 refers to the model number. The other numbers must refer to date code.
Replies: 4
Views: 567
Posted By longtimealaskan

Thank you. Any idea what the number is on the...

Thank you. Any idea what the number is on the carburetor flange (5297L25)? I assume the carburetor is a Tecumseh.
Replies: 4
Views: 567
Posted By longtimealaskan

Question about Tecumseh carburetor

I have a carburetor left over from an old trashed lawn mower. I think the carburetor is a Tecumseh (Tecumseh Products Co. is written on the bowl), but the part number does not match numbers I found...
04-19-15, 10:37 PM
Replies: 7
Views: 23,905
Posted By longtimealaskan

XSleeper I thought I'd report my progress...

XSleeper

I thought I'd report my progress and ask another question.

You are right about the glaze being like chewing gum. It sticks to everything. I removed as much of the glaze as possible...
04-16-15, 06:17 PM
Replies: 7
Views: 23,905
Posted By longtimealaskan

Thank you X Sleeper

49484Thank you for your thoughts and advice. I removed one of the smaller windows that open and took it to a glass repair shop today. The wood between the glass panes looks like they are strips...
04-16-15, 11:07 AM
Replies: 7
Views: 23,905
Posted By longtimealaskan

Replacing glass on old Pella casement window

Our house was built in 1974. It has Pella casement windows with all wood, no plastic. The interior glass pane, which is removable, is held in place by metal clips that can be pushed into a slot to...
Replies: 3
Views: 5,329
Posted By longtimealaskan

I think Delex is /was realted to Delta in some...

I think Delex is /was realted to Delta in some way. The fixtures look very similar. Delex is supposed to be a good brand. No I do not have access to the back wall. I prefer to repair the existing...
Replies: 3
Views: 5,329
Posted By longtimealaskan

Delex shower/tub converter vintage 1970's

I have a Delex single handle faucet system on my 1970's era bathtub. The faucet handle is in the center of a round chrome plate. Directly below the faucet is a chrome push button to push to convert...
Replies: 22
Views: 15,575
Posted By longtimealaskan

Avatar, I assume you got your boiler problem...

Avatar, I assume you got your boiler problem under control. I have a Lochinvar 105 and had the same problem you were having. Our boiler would take about 2.5 hours to bring the heat up in the...
Replies: 5
Views: 2,399
Posted By longtimealaskan

Smile Thanks Larry

Larry,

I got the roller off. I decided to try your suggestion about tapping it. I put a screwdriver on one end of the roller and put some upward pressure on it while tapping on the center shaft....
Replies: 5
Views: 2,399
Posted By longtimealaskan

Thanks Larry

Larry,

The drive roller is the rear roller and that is the one with the worn out bearing. The front roller is fine. I'm trying to figure out how to remove the rear roller.
Replies: 5
Views: 2,399
Posted By longtimealaskan

Question Belt sander repair

I have a Craftsman 3 inch belt sander and the sleeve bearing on the drive roller has worn out. I removed the retaining ring but can not get the rear roller off. Any advice how to remove the rear...
Showing results 1 to 12 of 12


 
Forum Jump