Search: Posts Made By: djwv1
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Replies: 6
Views: 7,138
Posted By djwv1

I need to figure a way to seperate the joint from...

I need to figure a way to seperate the joint from the stub axle first. The passenger side CV drive axle\ joint cannot be removed without either cutting the CV joint off at it's base, and sliding out...
Replies: 6
Views: 7,138
Posted By djwv1

Yea, you'd have a solid axle on a Cummins, the...

Yea, you'd have a solid axle on a Cummins, the only dodge I know of with cv joints ( and no coil springs too, mine has torsion bars instead) is the 4x4 1500 '02 and above. The 2500 , and the 2x4 1500...
Replies: 6
Views: 7,138
Posted By djwv1

I keep reading in posts that there's no cv joint,...

I keep reading in posts that there's no cv joint, as I hold the new cv joint, and read the section of the Hanes manual about removing said cv joint. The 02 1500 4x4 has fully independent suspension...
Replies: 6
Views: 7,138
Posted By djwv1

02 Dodge Ram 1500 4x4 cv joint stuck on stub shaft

I am replacing a passenger side cv joint on my 02 Dodge Ram 1500 4x4, and the stub shaft came out of the differential when I tried to remove it. It went back in no problem, and the snap ring...
Replies: 18
Views: 1,430
Posted By djwv1

Thanks for the great advice NJ! I called the...

Thanks for the great advice NJ! I called the first service company, the manager agreed to a full refund, plus to pay half of the burner cone repair. Also , signed up for a maintenance plan with the...
Replies: 18
Views: 1,430
Posted By djwv1

e showed me how the top came off, and the...

e showed me how the top came off, and the channels. he did not open them . I suppose I could and brush them out it isn't too difficult, it looked simple. The back is blown out, The back of the box...
Replies: 18
Views: 1,430
Posted By djwv1

had a different tech from a different company...

had a different tech from a different company today says last guy put on too small a nozzle. also, he broke the burner end cone (allegedly, I don't know for sure, but someone over torqued it, and it...
Replies: 18
Views: 1,430
Posted By djwv1

it ignites on it's own, just have to open the...

it ignites on it's own, just have to open the hatch and then close it to give it some air. He warned me flame can shoot out, so stand clear, and close it quickly. The black thing on the top he had...
Replies: 18
Views: 1,430
Posted By djwv1

it's a F75 45 pp, He showed me how to light it,...

it's a F75 45 pp, He showed me how to light it, it involves opening the hatch to the burner, and the thing fires right up. Otherwise it was taking several times to go. I am using diesel fuel, and...
01-22-14, 10:45 AM
Replies: 7
Views: 2,547
Posted By djwv1

several products are made to add into the...

several products are made to add into the birdseed, most are capsacin based. Birds cannot taste or smell well, so it does not bother them, and it does ok according to people who try it. Consider...
Replies: 18
Views: 1,430
Posted By djwv1

burner "dripping fuel, clogging air tube

My hydronic boiler system valliant w/ beckett oil burner recently started cutting off, and needing to have the reset button pushed to re-start. This is following a puff back, and a service guy doing...
12-02-10, 06:05 AM
Replies: 1
Views: 1,157
Posted By djwv1

furnace broke

my janitrol furnace keeps cutting off the exhaust motor cuts on and the elctronic pilot light comes on, but the burners will not ignite
Replies: 7
Views: 22,902
Posted By djwv1

alright-coded as a p0733-incorrect gear 3 ratio,...

alright-coded as a p0733-incorrect gear 3 ratio, transmission input rpm not matching transmission output rpm. the fluid was low too, by about a quart. I took it in, they want 950 to remove it and...
Replies: 7
Views: 22,902
Posted By djwv1

the cel has been on for some time. i forget the...

the cel has been on for some time. i forget the code, but I'm pretty sure transmission was part of it, I know that a vacuum leak was the other part. I originally wrote off the tranny b/c it was...
Replies: 7
Views: 22,902
Posted By djwv1

02 dodge ram 1500 speed sensor location

my 02 dodge ram 1500 is not shifting gears properly. I think it is the speed sensor, the truck was asymptomatic until today, and it barely will shift into third, and there is a lot of jerking when it...
Replies: 1
Views: 757
Posted By djwv1

baseboard heat gurlgeling

Anyone have suggestions about reducing/eliminating gurgeling in baseboard? I have an oil boiler, and the heat seems to be working good. Just a lot of noise. It ia a one-level house if that matters. ...
Replies: 2
Views: 1,325
Posted By djwv1

b/s 6.5 intek engine won't stay running

I have a JD mower with a b/s 6.5 intek engine. The mower starts strong, but dies a few seconds after. If I pump the primer, It wil keep going. I tried running it with the gas cap off, and also...
Replies: 1
Views: 910
Posted By djwv1

vaillant combi boiler not working

My Combi boiler stopped working this afternoon-it has plenty of oil, when i press the reset, I hear the fan, the click, all of it, just no fire-any ideas?
Replies: 3
Views: 1,644
Posted By djwv1

how is the line behind the unit bled? I have...

how is the line behind the unit bled? I have bled all the radiators-so must be air in the last line-Thanks!
Replies: 3
Views: 1,644
Posted By djwv1

boiler not circulating

I had to drain my boiler/hot water heater to remove a radiator. I filled it back up, now lots of hot water, no heat. the circulating pump is hot, but the pipe above it does not get hot. any ideas on...
Showing results 1 to 20 of 20


 
Forum Jump