Search: Posts Made By: edpdx
Showing results 1 to 11 of 11
Search took 0.01 seconds.
10-23-14, 02:18 PM
Replies: 5
Views: 1,963
Posted By edpdx

firedawgsatx, Thanks again, looking forward...

firedawgsatx,

Thanks again, looking forward to that info, sounds doable. It's pouring rain now, but when it lets up I'll take a stab at resetting the switch.
10-23-14, 12:25 PM
Replies: 5
Views: 1,963
Posted By edpdx

firedawgsatx, thanks. I'm on my way out to have a...

firedawgsatx, thanks. I'm on my way out to have a look at it. Was I right thinking that the switch can only be replaced after vacuuming the system?
10-23-14, 11:26 AM
Replies: 5
Views: 1,963
Posted By edpdx

Replaced contactor in Heat Pump still no fan.

My Ruud 10seer has been running pretty well. But a week ago the fan stopped coming on when the thermostat called for it.

I replaced the contactor because the old one looked a little burnt. I...
10-17-14, 04:29 PM
Replies: 1
Views: 656
Posted By edpdx

Ruud awakening. heat Pump fan does not heed the call.

My electric furnace comes on as it should but after feeling only a breeze at the registers, I looked into the heat pump to see that the blades were not spinning. I have a RUUD thermostat, Coleman...
Replies: 10
Views: 13,721
Posted By edpdx

:beers: RESOLUTION ! :beers:

Cheese. It seems that about the time you were posting you last idea that the pawls were not engaging because they were somehow bent too low, I was outside bending those little mothers up to reach...
Replies: 10
Views: 13,721
Posted By edpdx

Yes, I replaces it and the spring below it. When...

Yes, I replaces it and the spring below it. When I pull the starter rope it sounds as if the pawls are skipping across the plastic gear on the part you just mentioned.
Replies: 10
Views: 13,721
Posted By edpdx

No, it can't be the plastic that is worn down, as...

No, it can't be the plastic that is worn down, as I said, I replaced the starter coil and the starter spring. The plastic teeth the pawls engage are brand new.

I pulled the fly wheel and the key...
Replies: 10
Views: 13,721
Posted By edpdx

I have had it open about 6 times. The pawls are...

I have had it open about 6 times. The pawls are both springy and operate cleanly. I can see the clutch and clutch drum spin, but only sometimes. I am wondering it I somehow seated the flywheel too...
Replies: 10
Views: 13,721
Posted By edpdx

Pull start on trimmer does not engage

I just put a new starter spring and starter in my Troy Bilt TB525CS trimmer. The cord retracts ok, but something is not engaging. There is almost no resistance. Sometimes I hear and feel the piston...
04-06-14, 10:44 PM
Replies: 7
Views: 871
Posted By edpdx

I've done this before...

A tree cutting service I hired left after getting paid, but their flatbed truck hit a pothole causing the truck to snap off the last 4x4 on my fence. Since the post was toast and the concrete would...
04-06-14, 11:50 AM
Replies: 2
Views: 953
Posted By edpdx

Fencing at RISK... please help.

I build this wooden fence before there was a neighbor on the down slope side of my backyard. A few months later they parceled out a lot and built a home. After the new home was complete with the...
Showing results 1 to 11 of 11


 
Forum Jump