Search: Posts Made By: c2z4s9
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Replies: 13
Views: 2,429
Posted By c2z4s9

Chandler, Thank you very much for the...

Chandler,

Thank you very much for the assessment. I did go on the garage side and checked for lag screws coming through the siding and didn't see any. I then put some screws into the ledger next...
Replies: 13
Views: 2,429
Posted By c2z4s9

Thank you all very much for your answers and...

Thank you all very much for your answers and thoughtful comments. To my main concern however, it seems the general consensus is that the breezeway is structurally sound even though we recently added...
Replies: 13
Views: 2,429
Posted By c2z4s9

Chandler, the sub flooring in the breezeway...

Chandler,

the sub flooring in the breezeway is 1/2", but it has floor leveler on it and tile (5 lbs each 12 x 12 tile). The wood that looks bad on the end is the only one that doesn't look...
Replies: 13
Views: 2,429
Posted By c2z4s9

66218 OK, i figured out that my pictures...

66218

OK, i figured out that my pictures were too large to be uploaded. This is a bad picture, but it shows the inside of the garage where nails holding the ledger on are coming through the...
Replies: 13
Views: 2,429
Posted By c2z4s9

66215 Most of the spaces between joists have...

66215
Most of the spaces between joists have lag scrws in them. As I said I'm not positive where they are going on the garage side, but I don't see any protruding through the siding.

66216
Some...
Replies: 13
Views: 2,429
Posted By c2z4s9

I'm not sure if I can upload more than one...

I'm not sure if I can upload more than one picture at a time. Here is a picture of the front of the breezeway.

66210

When I attempt to upload additional pictures it says simply "Upload of file...
Replies: 13
Views: 2,429
Posted By c2z4s9

Yes, I should be able to provide pictures. I...

Yes, I should be able to provide pictures. I will try to do that tonight.
Thank you.
Replies: 13
Views: 2,429
Posted By c2z4s9

Unsupported Breezeway

Hello all,

The previous owner of my home recently built a garage and breezeway before I bought the home. The home has a full foundation, and the garage is essentially on a concrete slab, but...
03-03-11, 01:38 PM
Replies: 16
Views: 6,545
Posted By c2z4s9

Thanks for all the information. Sorry, I've been...

Thanks for all the information. Sorry, I've been away from this a bit.

I adjusted the weight so the damper is open about 1/2 when the furnace is running.

I did not check the pressure on the...
02-17-11, 06:26 AM
Replies: 16
Views: 6,545
Posted By c2z4s9

What do you think about closing the draft a...

What do you think about closing the draft a little bit? Since I have a power vent, I assume the draft on the furnace isn't really going to be changing all that much from one run to another, and...
02-17-11, 06:09 AM
Replies: 16
Views: 6,545
Posted By c2z4s9

Oh, and I do believe putting in the new...

Oh, and I do believe putting in the new electrodes did help with the smoke issue. It smokes less, but still smokes. I'll report back after I put in the new post purge unit.
02-17-11, 05:50 AM
Replies: 16
Views: 6,545
Posted By c2z4s9

It's a "field controls" power venter, similar to...

It's a "field controls" power venter, similar to the "SWG-5S", but it only has a 3" inlet. I was thinking of using metalbestos up the side of the house. Unfortunately, it's pretty obvious why they...
02-16-11, 05:51 PM
Replies: 16
Views: 6,545
Posted By c2z4s9

Grady, Thanks for the reply! It's too bad I...

Grady,

Thanks for the reply! It's too bad I already bought the guage... oh well :). I didn't end up adjusting the dimension in any way -- seemed close enough for me. Anyway, the nozzle you...
02-16-11, 05:44 PM
Replies: 16
Views: 6,545
Posted By c2z4s9

OK, so I checked and I was actually wrong about...

OK, so I checked and I was actually wrong about the model, etc. I was close, but not quite right. here is the closest I can come given what Beckett has listed on their site.

Rheem Manufacturing ...
02-16-11, 03:00 PM
Replies: 16
Views: 6,545
Posted By c2z4s9

so I did a little more digging and I found this...

so I did a little more digging and I found this info about the furnace:

Rheem Manufacturing ROBC-095 AFG F3 2-3/4" 0.85 X 70B 5880 AF42XNHS 100 B2007 S-10 / B-0 3-11/16"

AF42XNHS...
02-16-11, 08:13 AM
Replies: 16
Views: 6,545
Posted By c2z4s9

Reducing Smoke; Beckett AFG Burner

Hello All,

I have a long post, so please bear with me.

I bought a house a few months back, and was pretty ignorant to all things furnace related. The house has an old forced hot air Rheem oil...
Showing results 1 to 16 of 16


 
Forum Jump