Search: Posts Made By: etquint
Showing results 1 to 19 of 19
Search took 0.01 seconds.
Replies: 11
Views: 22,180
Posted By etquint

Well I removed the fuel tank, cleaned it and...

Well I removed the fuel tank, cleaned it and installed a new fuel pump. Because I put in a new pump, I have not checked for volume, yet. Fuel pressure is over 30 PSI and it still has a hard time...
Replies: 11
Views: 22,180
Posted By etquint

The engine is not putting out any check engine...

The engine is not putting out any check engine codes, but I just found out that after I changed my fuel filter the pressure went up to 34-35 PSI. I also noticed some small particles and what appears...
Replies: 11
Views: 22,180
Posted By etquint

Smile 1993 Ford Ranger Fuel Pressure

My manual says my working fuel pressure should be 35-45 PSI.
My fuel guage reads 31-32 PSI when it is running. Is that enough pressure? When I try to start the truck the fuel pump does not stop...
Replies: 2
Views: 1,019
Posted By etquint

1993 Ford Ranger

The engine is a 6 cylinder 4.0. It just seems to have a hard time starting. The 40 PSI goes to 31-32 PSI as soon as it starts. I disconnected the vacuum line to the regulator and the pressure goes...
Replies: 2
Views: 1,019
Posted By etquint

Smile 1993 Ford Ranger Problem

This is a continuation of 8/15/09. Well, things have changed now. Yesterday was the first day I used the fuel pressure guage. Yesterday, sometimes the pressure would go up to 10 PSI when I first...
Replies: 5
Views: 1,679
Posted By etquint

Well, things have changed now. Yesterday was the...

Well, things have changed now. Yesterday was the first day I used the fuel pressure guage. Yesterday, sometimes the pressure would go up to 10 PSI when I first turned on the key, not running, but the...
Replies: 5
Views: 1,679
Posted By etquint

1993 Ford Ranger Problem

My standard truck runs rough sometimes and sometimes stalls out and is sometime hard to restart. It's like it is not getting any fuel. I have already changed the fuel filter. I just checked the fuel...
Replies: 1
Views: 1,274
Posted By etquint

Smile 1993 Ford Ranger RPM Unsteady

My Ford seems to have a few problems. I'll start with one problem at a time. Right now after it sat for over a week, it died on me on the way to work. It took awhile, but it finally started and it...
Replies: 8
Views: 5,180
Posted By etquint

For me it would be easier, if I could install the...

For me it would be easier, if I could install the magnet from underneath the car. I have pulled an oil pan before from a 1991 Buick 3.8 engine without having to remove the engine. And it was a lot...
Replies: 8
Views: 5,180
Posted By etquint

This is definitely not a quick reply, but I found...

This is definitely not a quick reply, but I found out that my 3.8 engine has a plastic camshaft magnet. Through the camshaft sensor opening I noticed that the plasitic piece was broken and did not...
Replies: 3
Views: 1,016
Posted By etquint

1991 Park Ave Timing Chain Cover Removal

My maintenance manual is not very clear about removing the timing chain cover. Does the water pump have to come off before you can get to all the nuts and bolts to remove the timing chain cover?:)
Replies: 8
Views: 5,180
Posted By etquint

Thanks! And have a great evening!

Thanks! And have a great evening!
Replies: 8
Views: 5,180
Posted By etquint

Thanks for the info! Do you agree with the...

Thanks for the info! Do you agree with the possibility of the magnet falling off? Also, do you know what kind of problems this has on the car. It seems to run fine.
Replies: 8
Views: 5,180
Posted By etquint

Smile 1991 Buick Park Ave Code 41

My car has a Code 41 fault which is a cam sensor signal fault. I have checked the wiring, and it checks out good. I replaced the cam sensor and it still has the fault. I even replaced it with ...
Replies: 1
Views: 5,322
Posted By etquint

Smile A/C Pressure Readings

I installed a used A/C compressor on my 1991 Buick. Not sure if it was good to begin with. Anyway, I pulled a vacuum and it held very well. When I started to charge the system with R134A, it took the...
Replies: 2
Views: 2,232
Posted By etquint

Smile A/C Vacuum Leak

When a vacuum is pulled on an A/C sytem in a auto and the vacuum does not hold, is there a way of finding out where the vacuum is leaking? Thanks!
Replies: 1
Views: 1,165
Posted By etquint

Smile A/C compressor Seals

I purchased a used Delphi 6552 A/C compressor to replace a HR6HE compressor for a 1991 Buick Park Avenue. I bought it with no warranty. Mine was mounted on the car at the time.They are exactly alike...
Replies: 1
Views: 835
Posted By etquint

Power Steering Too Unbelievable!!

I have a 1989 Dodge Dakota. The problem is you just barely turn the steering wheel (it has power steering) and it turns the steering at a very quick rapid rate. I mean too fast! And the wheels turn...
Showing results 1 to 19 of 19


 
Forum Jump