Search: Posts Made By: jondabomb
Showing results 1 to 21 of 21
Search took 0.01 seconds.
Replies: 25
Views: 4,704
Posted By jondabomb

I followed your test...

The transmitter was bad. I bridged the hardwire and it opened while I was away (saying check zone)
So i swapped out another 5816 and ill see if it opens.
Which glass break sensor do you recommend...
Replies: 25
Views: 4,704
Posted By jondabomb

No- its an ademco 5816 w/..

Its a wireless ademco 5816mn with a sentrol ge security 584503-w glass break sensor.
The ademco 5816 is in a box with this sensor and a positive lead and a negative lead go in front of the positive...
Replies: 25
Views: 4,704
Posted By jondabomb

replaced battery still getting check...

I replaced the battery last night around 9pm and the unit worked fine until 8am this morning. It looks like a wireless 5816 with the sensor that connects at the battery terminals.
Should I just...
Replies: 25
Views: 4,704
Posted By jondabomb

Follow-up

Normally, when you release the cover it sends out a signal that indicates that it is open, and sounds a chime to go along with that...
Were you able to tell, via the last message, if the settings...
Replies: 25
Views: 4,704
Posted By jondabomb

current settings

Zn=13 zt=4 p=1 rc=10
Interior follower=04
partition=1
in=l
rf:1s
report =1st =01
rf=3
l=1

Interestingly when i exit out of the programming mode, everything works and it returns to normal,...
Replies: 25
Views: 4,704
Posted By jondabomb

New problem?

Now, my wireless glass break sensor wont reset. It says that there is a glass break in the bedroom (which there isnt).
it was working fine, and then when I came home it said that "check 13 bedroom...
Replies: 25
Views: 4,704
Posted By jondabomb

i believe i figured it out!

I disabled all zones up until 8 which was for the box and following the sheet the original installer left, i was able to confirm everything and now it all works.
Without the support of this forum i...
Replies: 25
Views: 4,704
Posted By jondabomb

Ok.. making progress!

Ok, so I know what the problem was. I was trying to program into a hard wired zone. Now I need to delete what I tried to do into zone 6, im able to get into zone 6, but do I just enter zero's into...
Replies: 25
Views: 4,704
Posted By jondabomb

How can I repair the fault I caused?

I tried to add a new wireless transmitter to my vista 20p and followed the directions that Ron had posted.
I went to program mode
*56
1
i entered the zone # which was 6 for the window, but it...
Replies: 25
Views: 4,704
Posted By jondabomb

fault 6

I might have made things worse because now it says fault 06..
Ill look in the manual again and follow your directions...
Replies: 25
Views: 4,704
Posted By jondabomb

I looked in the installer manual but I couldnt...

I looked in the installer manual but I couldnt find information about swapping out a contact or deleting the old serial number and putting in the new serial number. All the setting should remain the...
Replies: 1
Views: 16,323
Posted By jondabomb

Error Check 90 Receiver Jam

I have a vista 20p with the alpha keypad w/out mike.
today, all of a sudden, im getting the message and a intermittent beep that says check 90 receiver jam.
Any ideas?
Replies: 25
Views: 4,704
Posted By jondabomb

ademco vista 20p kypad

It appears that I have the standard alpha display keypad, as there are mis spelled words and it identifies the location of the sensors..
Replies: 25
Views: 4,704
Posted By jondabomb

Purchasing a new wireless motion detector and window contact

When I purchased my place it came with a ademco vista 20p (bay alarm)
Bay wouldnt help me in any way unless i subscribed to their service. Using this website, I was able to successfully reconfigure...
Replies: 5
Views: 1,190
Posted By jondabomb

Bathroom sensor missing, can I just purchase a replacement transmitter?

Thanks, ill follow the directions in the faq. The bathroom is missing its sensor, its all wireless. I think someone threw it away. Instead of deleting that zone can I just purchase a new sensor for...
Replies: 5
Views: 1,190
Posted By jondabomb

your thoughts were correct!

I hadnt opened the door so it reverted back to stay.
Now, my only problem is that it says comm. failure, which I attribute to not having phone service. How do I make this a local only system, one...
Replies: 5
Views: 1,190
Posted By jondabomb

Vista 20-p, unplugged for several months. Did it reset?

Ok, I finally got into my control panel and got the master code. I ran a test, but the system, except for the door is all wireless. The motion detector doesnt light up when I walk by, but when I...
Replies: 7
Views: 4,241
Posted By jondabomb

It requires that you know the master code to make...

It requires that you know the master code to make the changes?
Adding a User Code: Master code + [8] + 2-digit user no. + userís code
Replies: 7
Views: 4,241
Posted By jondabomb

Same question, but unable to locate master code

I have a similar situation in which I purchased a house with the vista 20p
I followed the directions and downloaded the install manual and got the installer code (2020) but there is nowhere (that I...
Replies: 21
Views: 73,971
Posted By jondabomb

update, fault in zone 8 was alarm box door

I still am unable to arm/unarm the unit. I followed all directions, and the installer code, which i believe is 2020 does nothing. I am downloading the compass software, but I am unfamiliar with it....
Replies: 21
Views: 73,971
Posted By jondabomb

vista 20p

Greetings, I have followed the instructions in the faq regarding retrieving the installer code for the vista 20p. It doesnt seem to be locked out. I press *# and the it says installer code. I press...
Showing results 1 to 21 of 21


 
Forum Jump