Search: Posts Made By: YesHaveSome
Showing results 1 to 25 of 43
Search took 0.01 seconds.
Forum: Water Heaters
10-20-20, 09:03 AM
Replies: 8
Views: 807
Posted By YesHaveSome

I assume you mean the heat/gas to the water...

I assume you mean the heat/gas to the water heater and not the furnace?
Forum: Water Heaters
10-19-20, 09:43 PM
Replies: 8
Views: 807
Posted By YesHaveSome

Shut er down tonight and it's in the process of...

Shut er down tonight and it's in the process of draining. Gonna replace it tomorrow after work. Thanks for the advice all.
Forum: Water Heaters
10-19-20, 03:21 PM
Replies: 8
Views: 807
Posted By YesHaveSome

Leaking hot water heater...how long do I have?

Hey everyone,

I noticed my HWH is leaking. It was just a small trickle last night but it's grown a little bit today. I am going to replace myself but can't do it right away. Am I good to wait a...
10-05-18, 10:54 AM
Replies: 2
Views: 925
Posted By YesHaveSome

Ah, that's a jumper. Thanks!

Ah, that's a jumper. Thanks!
10-05-18, 10:28 AM
Replies: 2
Views: 925
Posted By YesHaveSome

Help wiring a thermostat

Morning all,

I am installing a new thermostat and have a couple of questions.

Here's the thermostat in question:...
Replies: 4
Views: 712
Posted By YesHaveSome

Kitchen sink drain line...is this right?

Morning all,

Working on a house flip and went to install the garbage disposal on Sunday and the drain line seemed too high (we had the rough plumbing done by a plumber). Called the plumber out...
Replies: 3
Views: 1,112
Posted By YesHaveSome

It does require a permit and that connection we...

It does require a permit and that connection we used is to code for our area. I am in KCMO.
Replies: 3
Views: 1,112
Posted By YesHaveSome

Deck Stair Landing Issue

Evening all,

I am building a deck on a house I recently bought. I ran into a problem today that I cant figure out and am all ears to any advice.

I cut the stair stringers and we started to put...
Replies: 2
Views: 610
Posted By YesHaveSome

Galvanized confusion

Hey all,

I am building a deck and researching flashing. Everything I've read says not to use galvanized flashing because it reacts with PT lumber yet galvanized fasters and hardware (nails, joist...
Replies: 9
Views: 1,786
Posted By YesHaveSome

Cat Pee Soaked Pad Stuck to Hardwood Floor

Evening all,

I started demo on a house I am flipping today and when we pulled up the carpet the pad has basically fused with the hardwood flooring. I spent an hour or so with a putty knife and...
01-29-18, 07:17 AM
Replies: 8
Views: 3,148
Posted By YesHaveSome

Thanks. Do you see any issue running EMT on the...

Thanks. Do you see any issue running EMT on the outside or should I use PVC?
01-28-18, 08:47 PM
Replies: 8
Views: 3,148
Posted By YesHaveSome

EMT Raintight Connections

Evening all,

I need to run a circuit to an a/c disconnect on the side of my house. I have conduit running on the ceiling and then need to take it through the wall and down the outside of my house...
01-28-18, 01:33 PM
Replies: 1
Views: 2,227
Posted By YesHaveSome

Mini Split Installation - how to seal the wall penetration

I am doing a mini split install and am wondering how best to seal the wall penetration. It's a 2x4 stud wall with lap wood siding. The kit came with a couple of sleeves but they will on fit on the...
01-27-18, 01:16 PM
Replies: 4
Views: 1,118
Posted By YesHaveSome

What size breaker?

I am installing a mini split and nowhere in the manual does it state what size breaker is required. It's an 18,000 unit and based on other research I have done this usually requires a 30A breaker. ...
01-26-18, 08:26 PM
Replies: 3
Views: 1,878
Posted By YesHaveSome

I do a lot of woodworking so there's more than a...

I do a lot of woodworking so there's more than a usual garage but I have dust collection on every tool and keep it controlled pretty well. I talked to a lot of guys that have mini splits in their...
01-26-18, 08:05 PM
Replies: 3
Views: 1,878
Posted By YesHaveSome

Mini Split Placement

Good evening,

I am installing a mini split in my garage shop and have a question regarding where it should be placed. There is a picture attached with the floorplan of my shop with my two options...
01-26-18, 07:47 PM
Replies: 8
Views: 1,221
Posted By YesHaveSome

Ah, yeah, I looked into it a bit more and the...

Ah, yeah, I looked into it a bit more and the THHN I have on hand is also THWN.

In regards to the romex, I am trying to decide if I want to have conduit on the outside of my house.

Thanks for...
01-26-18, 01:55 PM
Replies: 8
Views: 1,221
Posted By YesHaveSome

Thanks. I'll have to check with my local code...

Thanks. I'll have to check with my local code people. I've heard that they dont like EMT on the outside.
01-26-18, 01:52 PM
Replies: 8
Views: 1,221
Posted By YesHaveSome

Thanks for the reply. I was looking online...

Thanks for the reply.

I was looking online for THWN and it seems that finding it by the foot might be a problem. What if I ran conduit to the wall and then ran the wire down in the wall and into...
01-26-18, 09:42 AM
Replies: 8
Views: 1,221
Posted By YesHaveSome

Mini Split Installation - Electrical Question

Morning all,

I am installing a Pioneer mini split in my garage workshop. I will be doing most of the installation myself and an HVAC tech will do final connections and vacuuming of the system. ...
11-07-17, 05:44 PM
Replies: 1
Views: 1,467
Posted By YesHaveSome

Sub Panel Grounding

I am installing a subpanel in my garage. I have everything in the panel wired up and am now getting ready to connect it to the main panel. I want to make sure have the ground/neutral squared away...
11-03-17, 08:28 AM
Replies: 3
Views: 884
Posted By YesHaveSome

Thanks for the info, everyone. I am hanging...

Thanks for the info, everyone.

I am hanging them because I have conduit running on the ceiling and need to get the lights below the conduit.
11-02-17, 09:38 PM
Replies: 3
Views: 884
Posted By YesHaveSome

Strip Light Fixture Installation

Evening all,

I am installing a few LED strip light fixtures in my garage. Here is the model: https://www.1000bulbs.com/product/192389/PLT-20015.html

I have a couple of questions:

1) The...
10-29-17, 06:37 PM
Replies: 9
Views: 1,878
Posted By YesHaveSome

Yep, it worked. It was still pretty snug but I...

Yep, it worked. It was still pretty snug but I was able to get it all in there.
10-28-17, 08:50 PM
Replies: 9
Views: 1,878
Posted By YesHaveSome

I just realized that I am using 1 1/2" deep...

I just realized that I am using 1 1/2" deep boxes. I thought I was using 2 1/8". Gonna swap em out and it should go a lot easier.
Showing results 1 to 25 of 43
 


 
Forum Jump