Search: Posts Made By: HOTDIY
Showing results 1 to 25 of 114
Search took 0.02 seconds.
Replies: 6
Views: 476
Posted By HOTDIY

Glad to hear that, thank you.

Glad to hear that, thank you.
Replies: 6
Views: 476
Posted By HOTDIY

Thank you for the PDF file. I think itís 389cc.

Thank you for the PDF file. I think itís 389cc.
Replies: 6
Views: 476
Posted By HOTDIY

A little rusty. Heat shield took the brunt of...

A little rusty. Heat shield took the brunt of the rust. How would I clean out the mud daubers?
Replies: 6
Views: 476
Posted By HOTDIY

Generac generator rebuild

I have a Generac GP7500E Iím slowly rebuilding. Sat in a shed for years. Rusty parts, mud dauber nests, etc. Replacing the ignition coil, carburetor, fuel line. Might be able to save the fuel...
Replies: 9
Views: 742
Posted By HOTDIY

I was on a slight incline and no oil leaked. ...

I was on a slight incline and no oil leaked.

A couple of notes:
The oil sender is located kind of elevated behind the alternator on the engine block.

Also it is angled towards the front...
Replies: 9
Views: 742
Posted By HOTDIY

Roger that. Thanks PJ, appreciate the help.

Roger that. Thanks PJ, appreciate the help.
Replies: 9
Views: 742
Posted By HOTDIY

So the oil should trickle out and Iím quick with...

So the oil should trickle out and Iím quick with the change I should be ok, right?
Replies: 9
Views: 742
Posted By HOTDIY

Oil Sender Unit

2013 F150 Lariat 5.0 oil sender unit is acting up and Iím changing it out. Do I need to drain the oil?
Replies: 5
Views: 1,034
Posted By HOTDIY

Thanks Pj, I presume the bottom is the three tabs...

Thanks Pj, I presume the bottom is the three tabs that are circled. I'll try it tomorrow after work.
Replies: 5
Views: 1,034
Posted By HOTDIY

Gentle isn't working. Tried a hammer, tried...

Gentle isn't working. Tried a hammer, tried bending/angling the blade down/up and using the hammer. Only goes in about 3/8". Any tips/tricks?
Replies: 5
Views: 1,034
Posted By HOTDIY

LG Refrigerator Ice Dispenser Switch

I have an LG fridge model LFXS28566S that I need replace the dispenser switch. It's sticking and causing ice/water to continue to pour. Watched some videos but want make sure I'm on the right path....
Replies: 5
Views: 549
Posted By HOTDIY

Mfg Part Number 6600JB3001C.

Mfg Part Number 6600JB3001C.
Replies: 5
Views: 549
Posted By HOTDIY

Just did. Need to figure out how to get to it.

Just did. Need to figure out how to get to it.
Replies: 5
Views: 549
Posted By HOTDIY

LG Refrigerator Water Dispenser

Got an LG fridge with a faulty water/ice dispenser. I believe that the sensor is stuck because it wants to dispense water/ice even when the mechanism isnít being pushed. Model number is LFXS28566S...
Replies: 1
Views: 239
Posted By HOTDIY

GE Profile Washer Model PTWN6050M0WT

I bought this washer at an estate sale for $40. Took it home and set it up outside to test it out. Good thing because it leaked bad. Turns out the shower head style water fill was clogged really...
Replies: 27
Views: 1,095
Posted By HOTDIY

The plastic parts are separate but something on...

The plastic parts are separate but something on the inside is keeping it connected. The whole thing should be apart by now. Iím wondering if the insulating material for the circuit board was poured...
Replies: 27
Views: 1,095
Posted By HOTDIY

Down the final connection at the noise filter and...

Down the final connection at the noise filter and it's fighting me. No burned or melted spots that I can see but it's stuck. In the picture it looks like it's apart but it's not. I'm pulling and...
Replies: 27
Views: 1,095
Posted By HOTDIY

I got it worked out. Needed to press near the...

I got it worked out. Needed to press near the bottom middle with a small screw driver and pull. What a pita!
Replies: 27
Views: 1,095
Posted By HOTDIY

A new weekend and a new attempt. In order for me...

A new weekend and a new attempt. In order for me to pound out the shaft I need to take the top off and disconnect the wiring. Having difficulty with these connections. I'm afraid I'll break the...
Replies: 27
Views: 1,095
Posted By HOTDIY

Thank you for the help it is appreciated.

Thank you for the help it is appreciated.
Replies: 27
Views: 1,095
Posted By HOTDIY

I suppose itís possible to take everything apart...

I suppose itís possible to take everything apart from below and pound it out from the top. Thoughts?
Replies: 27
Views: 1,095
Posted By HOTDIY

Trying to get the tub out so I can replace the...

Trying to get the tub out so I can replace the wash plate and washer clutch. The splines are worn down making a very bad grinding screeching noise and and no agitation.
Replies: 27
Views: 1,095
Posted By HOTDIY

Ok guys, I found out the source of the noise. The...

Ok guys, I found out the source of the noise. The splines on the wash plate and the splines on the drive shaft had worn down. I got the parts in and Iím not having much success getting the tub out....
Replies: 27
Views: 1,095
Posted By HOTDIY

All right guys, I watched the video and I tried...

All right guys, I watched the video and I tried that. I also tried holding for five seconds and then pushing the start button. No joy for any of this. But the noise definitely happens at the...
Replies: 27
Views: 1,095
Posted By HOTDIY

Iíll try that this afternoon when I get home. ...

Iíll try that this afternoon when I get home. Thank you.
Showing results 1 to 25 of 114
 


 
Forum Jump