Search: Posts Made By: caster
Showing results 1 to 25 of 200
Search took 0.02 seconds.
04-15-22, 08:26 PM
Replies: 1
Views: 177
Posted By caster

Plant and Weed/Root ID

Hello.

The second picture is a shrub I removed due to its poor condition. At the base of this shrub and through the soil I am finding the below root/weed. Curious if someone can identify this...
Replies: 2
Views: 301
Posted By caster

Condenser fan grill and motor rust

Hello.

Should I be replacing the fan grille or motor based on the below? Keep an eye on it?...
03-10-22, 04:00 PM
Replies: 5
Views: 182
Posted By caster

Yes the diagram posted doesnít show my exact...

Yes the diagram posted doesnít show my exact setup. The box I want the live common in does have a real neutral
03-10-22, 12:37 PM
Replies: 5
Views: 182
Posted By caster

Three way Switch moving Common to Other Box

I am wanting to wire a smart switch that requires a neutral to a three way switch setup in my home.

The three way switch I have currently is wired as below, as the common that is live is on the...
Forum: Water Heaters
10-24-21, 05:56 PM
Replies: 5
Views: 334
Posted By caster

The pressure tank I referred to is actually an...

The pressure tank I referred to is actually an expansion tank on the cold water side

there was never two heaters. I am the original owner.
Forum: Water Heaters
10-23-21, 03:34 PM
Replies: 5
Views: 334
Posted By caster

About 40 feet away on the main is the pressure...

About 40 feet away on the main is the pressure tank. This is the plumbing since the house was built.
Forum: Water Heaters
10-23-21, 01:50 PM
Replies: 5
Views: 334
Posted By caster

Direct vent water heater, two pressure valves

I have a natural gas powered vent water heater. It is just used for domestic water. Curious to know why I would have two pressure release values? One is one water heater and one is on the hot water...
Replies: 2
Views: 221
Posted By caster

So dry out with dehumidifier?Watch and beside...

So dry out with dehumidifier?Watch and beside grading donít take any action?

water appeared to come through where wall meets floor.
Replies: 2
Views: 221
Posted By caster

Slight damp spot basement

Early this morning we had heavy rainfall near 4". In my twelve years here, this is the first Ive seen water get in here in the basement (https://imgur.com/a/zIKEoOG) . House is a two story with...
06-18-21, 05:44 PM
Replies: 17
Views: 842
Posted By caster

It's done and this is what I did. No disconnect...

It's done and this is what I did. No disconnect required. Just breaker with lock. Subpanel is in sight .
06-17-21, 03:40 PM
Replies: 17
Views: 842
Posted By caster

Not really. My initial plan was have a box and...

Not really. My initial plan was have a box and get the ground there. Just seeing if there was another way
06-17-21, 07:28 AM
Replies: 17
Views: 842
Posted By caster

Appears I can use Liquid Tite flex metal conduit...

Appears I can use Liquid Tite flex metal conduit for about six feet and it would be the ground. Now the question is how would I attach the metal conduit in the liquid tite to a device that is in a...
06-16-21, 06:55 AM
Replies: 17
Views: 842
Posted By caster

Curious why you are saying this as NEC sees the...

Curious why you are saying this as NEC sees the EMT as a ground as long as it properly size for the wire inside.
06-16-21, 04:23 AM
Replies: 17
Views: 842
Posted By caster

Thought about that. I want all the wires...

Thought about that. I want all the wires protected as in garage
06-16-21, 04:19 AM
Replies: 17
Views: 842
Posted By caster

its a 60amp circuit using 4 AWG to future proof a...

its a 60amp circuit using 4 AWG to future proof a little
Running a neutral to have some flexibility
06-15-21, 07:05 PM
Replies: 17
Views: 842
Posted By caster

EMT to liquid tight fitting that keeps emt as ground?

I'm installing a charger. The EMT pipe I ran from my subpanel will serve as the equipment ground. One idea I had was to use a double gang box to convert to liquid tight. Inside this double gang...
06-12-21, 10:12 AM
Replies: 5
Views: 362
Posted By caster

measuring the knock out across its 1-11/16" . ...

measuring the knock out across its 1-11/16" .

Below is the panels info sheet. Under the KO diagram. The KO I want to use is the top side back left where it says 1-1/2"
...
06-12-21, 09:15 AM
Replies: 5
Views: 362
Posted By caster

1-1/2" Knockout is 1-1/2 Clamp?

Havent worked with 1/0 Aluminum SER Before and getting ready to feed some into my main panel. I am planning on using a 1-1/2 cable clamp to secure the cable to the service panel. My panel has an...
Replies: 8
Views: 693
Posted By caster

Going to use 8" block for the core and 4" block...

Going to use 8" block for the core and 4" block to make the ledge up till ground level or tad below
Replies: 8
Views: 693
Posted By caster

I called the town early this morning and they...

I called the town early this morning and they have no law preventing me from doing this. Town host quite a few of them already
Replies: 8
Views: 693
Posted By caster

Talking to a mason, he stated I should go down...

Talking to a mason, he stated I should go down below the frost level depth to prevent the heaving due to the freeze
Replies: 8
Views: 693
Posted By caster

Thank you for the reply. One last question. If...

Thank you for the reply. One last question. If my base is going to be 3'x3' does the foundation have to be that dimension to the frost line?
Replies: 8
Views: 693
Posted By caster

Brick Mailbox foundation

Hello. The frost line in my area is 36" . I plan on building a brick mailbox. In order to prevent it from heaving, it appears I should dig to 42" and put in 2" of pea gravel and then pour a...
02-17-21, 07:34 PM
Replies: 11
Views: 1,518
Posted By caster

I found the below link to backup the 2017 NEC...

I found the below link to backup the 2017 NEC rule you wrote above - https://www.electricallicenserenewal.com/Electrical-Continuing-Education-Courses/NEC-Content.php?sectionID=292.0

Do you have a...
02-13-21, 03:25 PM
Replies: 11
Views: 1,518
Posted By caster

its 48amps on a 60amp breaker

its 48amps on a 60amp breaker
Showing results 1 to 25 of 200
 


 
Forum Jump