Search: Posts Made By: Rakki
Showing results 1 to 12 of 12
Search took 0.01 seconds.
12-30-07, 10:28 AM
Replies: 2
Views: 1,063
Posted By Rakki

Unhappy Basement wall insulation for Metal Studs - Appropriate Batt width size

Any experiences by the forum members? Your suggestions will be valuable to me.

Additional question. Does providing insulation on the cinder block walls shared with neighbours in townhome provide...
12-28-07, 03:11 PM
Replies: 2
Views: 1,063
Posted By Rakki

Batts for basement walls with steel studs

Dear Sir,
I have 3 1/2" x 1 1/2" 25 gauge steel studs for the basement walls that are spaced 16". I was looking for 16" wide kraft faced batts since the batts needs to be tucked inside the hollow...
11-25-07, 04:16 PM
Replies: 4
Views: 11,552
Posted By Rakki

mmm. There is none listed in the package. Also...

mmm. There is none listed in the package. Also there are no recommendations/instructions in the shelf where I picked it up. (the items I have look exactly same as I shared in the link) The store guys...
11-25-07, 01:40 PM
Replies: 4
Views: 11,552
Posted By Rakki

Max wire limit in Clamp connector.

Can anyone tell me per code requirements how many 14/2 NM wires is allowed in the 3/4" & 3/8" clamp type connector?

For more description of the connector kindly view the below link.
...
11-20-07, 12:16 PM
Replies: 4
Views: 2,577
Posted By Rakki

Fastening wires to Metal Studs

Dear Sir,

I am doing electrical wiring for my basement. I have used metal studs. I couldnt find any standoffs for clamping the wires to the studs in Lowes or Home Depot. But I got some adhesive...
11-20-07, 12:01 PM
Replies: 20
Views: 12,419
Posted By Rakki

I am not sure but this is my rationale... I...

I am not sure but this is my rationale...

I see the two way switch as an XOR. If both the switches are in same position the lights will be off, on otherwise. So on/off position is not applicable...
11-16-07, 07:27 PM
Replies: 8
Views: 4,397
Posted By Rakki

Thanks again guys for the immediate reply. It...

Thanks again guys for the immediate reply. It helps a lot.
11-16-07, 06:31 PM
Replies: 8
Views: 4,397
Posted By Rakki

Max No of devices in a 14/2 wire

In a book by Roger German, it states "Code requires maximum 10 devices on a 14/2 wire".

I am wiring 10 recessed lights that are max 50W in the entertainment area. I am also planning to add 4 more...
11-16-07, 06:05 PM
Replies: 4
Views: 1,515
Posted By Rakki

Thanks much. It helps.

Thanks much. It helps.
11-16-07, 05:38 PM
Replies: 4
Views: 1,515
Posted By Rakki

Receptacle Height limitation

Dear Sir,
I am wiring a receptacle for a ceiling projector in my basement. Is there any electrical code that dictates the maximum height from the finished floor that a receptacle can be fixed?
...
08-12-07, 05:14 AM
Replies: 4
Views: 17,032
Posted By Rakki

Thanks Chandler. It was very helpful. Do you...

Thanks Chandler. It was very helpful. Do you know what size of metal stud is desired. Home Depot carries 3 5/8" and 2 1/2" steel studs (25GA). Also on the dangling Ls (made by 90 deg bend and one...
08-10-07, 10:38 PM
Replies: 4
Views: 17,032
Posted By Rakki

Using Metal Stud for Soffit

Is there any restriction in soffit size when using Metal studs.

What size of metal stud is desired for soffits.

Is there an efficient way to make the soffit. Like laying tracks on the stud...
Showing results 1 to 12 of 12


 
Forum Jump