Search: Posts Made By: indypower
Showing results 1 to 25 of 200
Search took 0.03 seconds.
09-02-11, 05:11 PM
Replies: 2
Views: 1,441
Posted By indypower

Ran out of oil, now no restart

I ran my furnace out of oil. I had 100 gallons delivered today. I can not get it to start. I have power to the burner as the light is on. I have pushed the rest button and nothing. It is a Utica with...
Replies: 4
Views: 953
Posted By indypower

No oil filter on that model. it is a "splash"...

No oil filter on that model. it is a "splash" system
Replies: 3
Views: 1,283
Posted By indypower

Here is a parts breakdown ...

Here is a parts breakdown

http://www.olsonspower.com/pages/oemparts?aribrand=HONPE#Error
Replies: 2
Views: 1,735
Posted By indypower

Onan is still in business. It was bought by...

Onan is still in business. It was bought by Cummings engines.

Onan Engines (http://www.cumminsonan.com/engines/)
Replies: 4
Views: 5,217
Posted By indypower

"hit a stump hard enough to shut mower off" ...

"hit a stump hard enough to shut mower off"
That is hard enough to break the flywheel key, which throws the timing off. I bet it tries to yank the pull handle out of your hand when you try to start...
Replies: 8
Views: 3,061
Posted By indypower

gas cap first, then coil. When it does die,...

gas cap first, then coil. When it does die, immediately check for spark.
Replies: 1
Views: 5,826
Posted By indypower

You can only buy the drive wheels from a Toro...

You can only buy the drive wheels from a Toro dealer. And the wheels may be your problem. They have the drive gear on the back of the wheels. I have had many in the shop that the teeth are broken off.
Replies: 9
Views: 5,922
Posted By indypower

intial carb settings are 1-1/2 turns out from...

intial carb settings are 1-1/2 turns out from lightly seated
Replies: 3
Views: 1,046
Posted By indypower

If you can post the model number, I can find you...

If you can post the model number, I can find you a parts list and maybe a service manual.
Replies: 6
Views: 1,480
Posted By indypower

I had never seen a thermostat on an air cooled...

I had never seen a thermostat on an air cooled small engine either, but here it is. #291. And since it is connected to the choke link,I would look into it further.

Parts and Diagrams for Briggs...
Replies: 5
Views: 7,795
Posted By indypower

You can remove the old seat using an o-ring...

You can remove the old seat using an o-ring scribe like this:
2 Piece O-Ring Hook Scribe Set (http://www.harborfreight.com/2-piece-o-ring-hook-scribe-set-42159.html)
Or you can try a small nail. As...
Replies: 4
Views: 991
Posted By indypower

can you post the engine numbers?

can you post the engine numbers?
Replies: 5
Views: 4,037
Posted By indypower

The law suit removed horsepower ratings. Don;t...

The law suit removed horsepower ratings. Don;t know who file the law suit or why (probably an engine maker against another engine maker). They really screwed up everything. Consumers know horsepower...
Replies: 1
Views: 2,493
Posted By indypower

If it has always done that, then I would say it...

If it has always done that, then I would say it was assembled with the augers on the wrong side or upside down. The augers pull snow into the middle. 1 other possibility is that the belt is routed...
Replies: 26
Views: 8,026
Posted By indypower

can you post the model number of the snowblower?...

can you post the model number of the snowblower? It may have been made by Ariens. Also, if you measure the diameter of the pulley and the hole sizes, you may be able to find an aftermarket one. Might...
Replies: 3
Views: 1,509
Posted By indypower

rinse everything that was soaked in warm water,...

rinse everything that was soaked in warm water, then blow out all holes with compressed air.
Replies: 3
Views: 1,355
Posted By indypower

That appears to have a Magnatron ignition, which...

That appears to have a Magnatron ignition, which means no points. However, the coil could be heating up and disconnecting inside. Next time it dies, immediatly check for spark.
Replies: 1
Views: 951
Posted By indypower

SnowChief was absorbed by MTD, but MTD no longer...

SnowChief was absorbed by MTD, but MTD no longer has parts for them. If you have the old belts, take them to NAPA and have them match them up. Make sure you tell them the belts are for a snow blower...
Replies: 2
Views: 1,961
Posted By indypower

To remove the impeller, you must "split" the snow...

To remove the impeller, you must "split" the snow blower in half. First, you must remove the belts. There are 2 bolts on each side at the rear of the scoop. Prop up the handle bars so they don't come...
Replies: 6
Views: 2,686
Posted By indypower

Remove the plug and clean the cylinder head...

Remove the plug and clean the cylinder head surface where the plug goes then get a new washer/gasket for the plug. What engine do you have?
Replies: 4
Views: 5,233
Posted By indypower

You still have a dirty carb. Most likely varnish...

You still have a dirty carb. Most likely varnish in the internal circuts. The only way I have found to get to those is by soaking in a carb cleaning solution. Spray carb cleaner is only good for dirt...
Replies: 1
Views: 972
Posted By indypower

what did you get? Gunk brand?

what did you get? Gunk brand?
Replies: 4
Views: 980
Posted By indypower

Many of the zerks are pressed in. I would replace...

Many of the zerks are pressed in. I would replace them with screw in zerks. Need a bottoming tap to tap the holes.
Replies: 4
Views: 1,047
Posted By indypower

You have a typo in the model number. It should...

You have a typo in the model number. It should read HMSK100. That being said, it is a L head engine.
Showing results 1 to 25 of 200
 


 
Forum Jump