Search: Posts Made By: Hammerhead
Showing results 1 to 25 of 25
Search took 0.01 seconds.
Replies: 2
Views: 892
Posted By Hammerhead

2001 Dodge Caravan

The motor on the passanger side window has gone out, or at least as far as i can tell, the window can come down but will not go back up . Is it a difficult job to replace myself?
Replies: 3
Views: 1,162
Posted By Hammerhead

Coughing 92 Chevy Silverado

I think my fuel pump is going out.
Idling the thing purrs like a kitten. When I accelerate from a stop It coughs and sputters. I've replaced the fuel filter. But I've been told it's the fuel pump....
Replies: 6
Views: 908
Posted By Hammerhead

thermostat

I replaced the thermostat and the needle still lays there. I checked the fuse and it looked good but I noticed when I removed it the temp guage rose a little while the other guages dropped. I...
Replies: 6
Views: 908
Posted By Hammerhead

could it be???

the temp needle on my 92 Chevy P/U just lays there. Is it a bad thermostat or could it be something else? Also while I'm replacing the thermostat ( if it is indeed bad) is there anything else I...
Replies: 6
Views: 963
Posted By Hammerhead

Thanks so much for your info. This all sounds so...

Thanks so much for your info. This all sounds so difficult to me or should I have it looked at by someone who knows what to do...or is it even worth pursuing or do I just go buy a new one?
Replies: 6
Views: 963
Posted By Hammerhead

Took the bottom off the belt is in tact. The...

Took the bottom off the belt is in tact. The machine rewinds and fast forwards just won't play.

Hammerhead
Replies: 6
Views: 963
Posted By Hammerhead

Picky VCR

I have an older model vcr that won't play. I've taken the cover off to look for any foriegn objects and found nothing unusual. I did notice that when I insert a video tape the tape gets pulled out...
Replies: 10
Views: 53,367
Posted By Hammerhead

hey ya'll I have an older model vcr that won't...

hey ya'll
I have an older model vcr that won't play.
I'll insert Dumb and Dumber and it rewinds, fast forwards normally but it won't play. I took the cover off to see if there were any foriegn...
Replies: 1
Views: 1,273
Posted By Hammerhead

92 Chevy Silverado

I think my starter is going out...pretty good for the factory starter. But at start up sometimes it sounds like it misses something, and then after a try or two it catches and turns over. Am I...
Replies: 3
Views: 1,479
Posted By Hammerhead

MAytag Heavy Duty Series 90

model # 92598200

Thanks Hammerhead
Replies: 3
Views: 1,479
Posted By Hammerhead

Kenmore Heavy Duty 90 Series

I have this washing machine, about 9 years old and it just recently began leaking. The drip pan it sits in as about 1/4 full and we have chose not use it until we can fix it. Lastnight I attempted...
05-10-04, 05:55 AM
Replies: 3
Views: 1,007
Posted By Hammerhead

yes, webs are present and it seems the infected...

yes, webs are present and it seems the infected limbs from the web up are dying.

thanks for the help
05-09-04, 03:55 PM
Replies: 3
Views: 1,007
Posted By Hammerhead

weed n feed n worms?

is it too late to apply weed and feed? And I have a crabapple tree that has... worms. The worms have made they're nest in joints of the tree and I'm not sure what to do. Should I spray? and what? or...
Replies: 19
Views: 17,001
Posted By Hammerhead

Craftsman Eager-1 6.5

Thanks for the help !!
Replies: 19
Views: 17,001
Posted By Hammerhead

Craftsman Eager-1 6.5

Yo Cheese,

Thanks for the reply!
I was in Wal-Mart and happened to check out the throttle links on some of the new mowers and noticed that I did have the link in the wrong hole. I'll look...
Replies: 19
Views: 17,001
Posted By Hammerhead

idle stop screw?

YO Cheese,

I Think it's the idle stop screw that I 've tightened down. My mower is self propelled. On the handle theres another handle that has to be held down to operate, then there's a lever...
Replies: 1
Views: 1,258
Posted By Hammerhead

Kenmoore Dryer model #96585210

So I have a feeling my heating element is going out, sometimes it takes several tries to dry completely, sometimes it does great.
Where should I start? Is there some place to get a diagram of...
Replies: 19
Views: 17,001
Posted By Hammerhead

Craftsman Eager-1 6.5

Hey Cheese,
Thanks again, so glad to have a place where real people can ask real questions and get a real answer.
I have the bowl with the screw on the bottom. In fact after I thought I...
Replies: 19
Views: 17,001
Posted By Hammerhead

many thanks

Just wanted to say thank you to the helpful folks on these forums. You were a huge help. SUCESS!!
Replies: 19
Views: 17,001
Posted By Hammerhead

Talking A million Thanks

to all that helped with the great info... THANK YOU!!
I sucessfully changed out the float and re-assembled the carb, and I must say it really wasn't too difficult with a little help from my ...
Replies: 19
Views: 17,001
Posted By Hammerhead

Carftsman Eager-1 6.5

how does one disassemble the carburator. Where do I start?
I get down there and it looks so complicated. Some one help me
03-31-04, 09:44 PM
Replies: 1
Views: 672
Posted By Hammerhead

Compost

Some tips on starting a compost? Are there some kind of methods to follow to yield rich, fertilized soil?

Thanks!
Replies: 148
Views: 200,680
Posted By Hammerhead

Dryer woas

I have a Kenmore 80 series heavy duty dryer that doesen't seem to be drying to well. I checked the lint tube to the outside vent and it was clear. My next guess is the heating element is gone out. Is...
Replies: 19
Views: 17,001
Posted By Hammerhead

craftsman egar-1

So, in taking the carburator apart...is that a diffucult project? I consider myself to be somewhat mechanically inclined but I've never taken apart a carburator. Can you reccommend a place to get...
Replies: 19
Views: 17,001
Posted By Hammerhead

Craftsman Eager-1

I own a Craftsman Eager-1 6.5 hp push mower. The problem I'm having is I'll prime it with a few pumps of the bulb and I'll start it. It'll run for a moment and then gas begins to pour out of the...
Showing results 1 to 25 of 25


 
Forum Jump