Search: Posts Made By: jdh79
Showing results 1 to 25 of 200
Search took 0.02 seconds.
Replies: 4
Views: 1,022
Posted By jdh79

When you hookup the pk5500 Im assuming the wired...

When you hookup the pk5500 Im assuming the wired one, you need to enter programming and do module reset 902. Once this is done, check the location where you enrolled your wt5500 keypad and be sure...
Replies: 4
Views: 642
Posted By jdh79

Red face You should be able to silence the voice...

You should be able to silence the voice altogether and hear only the beeps but I cant remember how.

# 2 1 ?? Function voice off. Might scan the keypad manual
Replies: 4
Views: 653
Posted By jdh79

Yes you can even use a jumper wire if you program...

Yes you can even use a jumper wire if you program the zone NC. But the system only knows what you tell it is there. So program as interior 05 or 06 and should work fine for what you want until you...
Replies: 3
Views: 562
Posted By jdh79

Interesting idea... you will need to enroll...

Interesting idea...

you will need to enroll in both panels the same and then change the button settings for the fob in each for the 2 buttons you want, turn opposite 2 off in each panel. Sounds...
Replies: 2
Views: 580
Posted By jdh79

Instead of the receiver number as your cell in...

Instead of the receiver number as your cell in field 41, use the follow me number I think it is field 46. Clear 41, *41*
Replies: 2
Views: 695
Posted By jdh79

First installer code. Used to enter programming...

First installer code. Used to enter programming but not regular arming / disarming. "Go to program" code sounds like alias possibly

User code and Master code. Both can arm / disarm system but only...
Replies: 17
Views: 3,428
Posted By jdh79

I would try to delete one of the zones and...

I would try to delete one of the zones and reenroll that sensor in s rf offered zone space. Then see if it works, better if you can use auto enroll with that transceiver.

Seems strange that this...
Replies: 4
Views: 653
Posted By jdh79

Do you have any motion detectors in the house? If...

Do you have any motion detectors in the house? If there are none programmed then it doesn't make any difference to the system and it will always arm as away.
Replies: 17
Views: 3,428
Posted By jdh79

Sounds like you need to set the attributes for...

Sounds like you need to set the attributes for each zone to wireless, option 8 on... Check you programming manual.
Replies: 2
Views: 497
Posted By jdh79

You need to enable the keypad address that you...

You need to enable the keypad address that you want to use. If you want to use address 20, you have to enter programming from an existing / working keypad. Enter *193 10.
*194 10 will enable address...
Replies: 46
Views: 10,257
Posted By jdh79

Its * 56 not # 56 The panel doesnt recognize...

Its * 56 not # 56

The panel doesnt recognize the #56 command because it cant show all the info stored there.

For entering information always use * key
Replies: 13
Views: 900
Posted By jdh79

6160rf can replace your 6128 no issues. No...

6160rf can replace your 6128 no issues.

No need for additional alpha keypad, it is independent in itself. Just set address to 31 should be default.

I think you have to enable rf capabilty on...
Replies: 46
Views: 10,257
Posted By jdh79

Any alarm system is made to call the monitoring...

Any alarm system is made to call the monitoring station when there is an alarm. All it takes is one call to send a signal and then the monitoring station will respond as necessary. It doesnt call...
Replies: 28
Views: 1,626
Posted By jdh79

Do you use the trigger scene while the system is...

Do you use the trigger scene while the system is armed?

Maybe even if armed stay only but not away, set the zone type as interior 04? Then report code 00 even if its monitored wont send alarm.
...
Replies: 5
Views: 1,016
Posted By jdh79

No problem. Just remember, never a bad idea...

No problem.

Just remember, never a bad idea to power down system before swapping keypads. I typically wouldnt myself but be careful not to short the wires together and potentially cause damage to...
Replies: 1
Views: 661
Posted By jdh79

See programming options for sections 501-514 and...

See programming options for sections 501-514 and 551-564. There are so many selections depending on how you set it up but give it a good read thru
Replies: 5
Views: 1,016
Posted By jdh79

Swap wires and address each keypad 31. Should be...

Swap wires and address each keypad 31. Should be default setting.

You can either use a jumper wire or disable zone 1 in programming *56. Set as type 00 * and 1 to confirm delete.
Replies: 5
Views: 1,016
Posted By jdh79

Your plan sounds good. 1 6160 keypad is all you...

Your plan sounds good. 1 6160 keypad is all you really need, it would be for your own preference if you added another. They also make a 6160rf for a little more money.

Keep in mind, you can use a...
Replies: 46
Views: 10,257
Posted By jdh79

*50 0 makes dialer delay 0. May be unable to...

*50 0 makes dialer delay 0. May be unable to change with adt default but no matter, it takes some time for that dialer to connect and call as well.

Once actual alarm starts then should be less...
Replies: 28
Views: 1,626
Posted By jdh79

What are the steps you are taking and what...

What are the steps you are taking and what exactly are you trying to make it do as the action?

Also note that you can only have 10 total scenes.

It may not allow the fob type 23 as trigger,...
Replies: 28
Views: 1,626
Posted By jdh79

Try zone type 23, no alarm response. If all you...

Try zone type 23, no alarm response. If all you want the button to do is activate a trigger then this will work best.
Replies: 11
Views: 1,011
Posted By jdh79

You should have an exit delay once you arm the...

You should have an exit delay once you arm the system in order to leave the house. Are you waiting long enough after arming it in order to set system into actual alarm state?
Replies: 8
Views: 1,154
Posted By jdh79

Make sure you have a small size straight...

Make sure you have a small size straight screwdriver even tho you have to twist it it wont fit a standard size screwdriver. Need about 1/4" or less wide. Just saying...
Replies: 4
Views: 698
Posted By jdh79

No programming is lost. Only if there were zone...

No programming is lost. Only if there were zone labels but there are not on your current keypad, the labels are stored in the keypad memory on these. The module reset itself will not erase anything....
Replies: 8
Views: 1,154
Posted By jdh79

First off, if the keypad says fault it just means...

First off, if the keypad says fault it just means it is open or detecting motion. If it says "check" then there is a problem.

They are kind of hard to pop open but you are correct. Should be...
Showing results 1 to 25 of 200
 


 
Forum Jump