Search: Posts Made By: wrench47
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 50
Views: 40,410
Posted By wrench47

Bear with me guys...........Is this a 2.4 4...

Bear with me guys...........Is this a 2.4 4 cyl?????..............Aluminum block AND head??????.........There's a bulletin on the headbolts pulling the threads out of the block on...
Replies: 3
Views: 1,197
Posted By wrench47

Throw out bearing gets noisey when clutch is...

Throw out bearing gets noisey when clutch is depressed..........loads the bearing and slows the input shaft of the trans.......Pilot bearing same thing........when clutch released input shaft and...
Replies: 12
Views: 10,537
Posted By wrench47

Came across an odd one last week........First...

Came across an odd one last week........First off........YOU don't turn the A/C on.........You ask the ECM to turn the A/C on ...........First the signal goes to the BCM which checks pressure at...
Replies: 5
Views: 2,011
Posted By wrench47

When changing the calipers, but not the lines,...

When changing the calipers, but not the lines, did you pinch off the rubber brake lines????....If so, there's your problem
Replies: 4
Views: 5,150
Posted By wrench47

These are good for fan motors......Before you go...

These are good for fan motors......Before you go nuts looking for diagrams........A test light to the motors plugs........with the A/C on engine running, do you have power ??????and do you have...
Replies: 3
Views: 1,911
Posted By wrench47

Gonna go out on a limb here and assume (dangerous...

Gonna go out on a limb here and assume (dangerous word) that you have an Aisan-Warner 4 speed auto........The older ones used to have a seperate trans control module with an inline fuse. Wire chafing...
Replies: 3
Views: 1,345
Posted By wrench47

Let's start with basics.......You confirmed spark...

Let's start with basics.......You confirmed spark and fuel........and compression is at 120?????.........I'd be pulling the timing cover to confirm belt alignment.......Could be off 1-2...
Replies: 10
Views: 1,996
Posted By wrench47

Dealing with a Mercedes......RW is right, first...

Dealing with a Mercedes......RW is right, first thing is to thoroughly read the owners manual with respect to required/requested maintenance.........As far as tires go, the real right tire would...
Replies: 13
Views: 7,443
Posted By wrench47

At the master, yes........but if it's bad enough...

At the master, yes........but if it's bad enough to not get a disengage I have a hard time seeing it work 3-4 times like he states........at the slave???......pressure gets to the slave and either...
Replies: 13
Views: 7,443
Posted By wrench47

While I agree, a bypass in the master/cyl may be...

While I agree, a bypass in the master/cyl may be a problem without fluid loss, If the master's workin and it's putting pressure to the slave and the slave doesn't move........where'd the...
Replies: 4
Views: 2,093
Posted By wrench47

Have the truck scanned....Not just codes.....Look...

Have the truck scanned....Not just codes.....Look in data for engine temp. A lying temp sensor will throw off the fuel mix......
Replies: 4
Views: 951
Posted By wrench47

Gentlemen, you have said it all..........Go IN...

Gentlemen, you have said it all..........Go IN with what came OUT........Don't cause problems.......Fix them
Replies: 13
Views: 7,443
Posted By wrench47

Shouldn't be a linkage problem.......#1 stick...

Shouldn't be a linkage problem.......#1 stick your head under the instrument panel and see if there's a trail of fluid running down the firewall from the rear of the CLUTCH master.......Then check to...
Replies: 7
Views: 3,747
Posted By wrench47

These are good for outer tie rod ends........Jack...

These are good for outer tie rod ends........Jack front wheel and see if there's excesive play...........Also....Is the vibration felt in the wheel or the seat of your pants????
Replies: 7
Views: 5,361
Posted By wrench47

Sensors are built into the hub...

Sensors are built into the hub bearings........And if it ha s front sensors, it has rears.......same deal, in the hub bearing
Replies: 7
Views: 5,361
Posted By wrench47

I'd go with a wheel sensor.........Almost willing...

I'd go with a wheel sensor.........Almost willing to bet a front one......Any humming from the front (or rear) sounds like you're being chased by an airplane????? Changes noise when turning left or...
Replies: 6
Views: 3,995
Posted By wrench47

You're giving a perfect description of low...

You're giving a perfect description of low coolant.....The heater core is the highest part of the system so you can overheat and have no heat at the same time. The fan sensor may not be getting...
Replies: 8
Views: 1,221
Posted By wrench47

Having the car checked thoroughly is task...

Having the car checked thoroughly is task #1...........Doing brakes on a 21 year old car before you make sure the engine/trans are sound might be putting $$$$$$ down a sewer.....Get an overall view...
Replies: 6
Views: 1,376
Posted By wrench47

Code readers.........YES they will tell you which...

Code readers.........YES they will tell you which circuit has an issue..........They WON'T tell you exactly where the issue is (Sensor/wiring/ECU) That's where a good DVOM, training and a ton of...
Replies: 10
Views: 1,611
Posted By wrench47

Basics.......Scan, check for stored codes, Fuel...

Basics.......Scan, check for stored codes, Fuel pressure /volume check (Customer states engine stall when gas pedal applied)..........and here's a good one.......You did the plugs (NGK/Nippondenso I...
Replies: 7
Views: 6,543
Posted By wrench47

Have someone stand outside and listen to the...

Have someone stand outside and listen to the strut plates as you turn the wheels back and forth.....If the noise is predominantly INSIDE the cab, be advised G.M. has had problems /bulletins on their...
Replies: 21
Views: 2,170
Posted By wrench47

Gotta love Lucas..........Having dealt with...

Gotta love Lucas..........Having dealt with English bikes........We refered to Lucas as the ..................."Prince of Darkness"
Replies: 4
Views: 1,359
Posted By wrench47

TFI module and/or pick-up coil in the...

TFI module and/or pick-up coil in the distributor............
Replies: 12
Views: 1,059
Posted By wrench47

Tempo/Topaz 2.3 HSC engines are NOTORIOUS for...

Tempo/Topaz 2.3 HSC engines are NOTORIOUS for cracking cylinder heads...........Is this vehicle losing coolant with no obvious external leaks?????
Replies: 8
Views: 819
Posted By wrench47

Really....to me.......It's a matter of how easy...

Really....to me.......It's a matter of how easy it is to do the pump............4.0 jeep is pretty much riht out in the open........I'd go reman.........Nowif it was a 2.4 in a PT Cruiser I'd get the...
Showing results 1 to 25 of 200
 


 
Forum Jump