Search: Posts Made By: David_Thompson
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 7
Views: 21,677
Posted By David_Thompson

check that all 4 suspension springs are...

check that all 4 suspension springs are connected. remove cabinet and make sure the 3 horizontal pads sitting in the frame that the skate plate slides on are not worn down. make sure rear legs self...
Replies: 3
Views: 2,442
Posted By David_Thompson

remove cabinet and make sure the 3 horizontal...

remove cabinet and make sure the 3 horizontal pads sitting in the frame that the skate plate slides on are not worn down. make sure rear legs self adjust when raising the rear of the washer also. a...
Replies: 167
Views: 140,513
Posted By David_Thompson

^check the lid switch. post model# if you need...

^check the lid switch. post model# if you need more help
Replies: 1
Views: 1,586
Posted By David_Thompson

this is one of those korean GE's made by LG, dont...

this is one of those korean GE's made by LG, dont think there is a tech sheet in that machine. if there is one it may be in the console
Replies: 3
Views: 1,930
Posted By David_Thompson

perhaps the drive block jumped off the basket...

perhaps the drive block jumped off the basket drive or the cam on the basket drive is broken.

remove the agitator and make sure the 2 tabs of the basket drive are fully seated in the drive block
Replies: 1
Views: 1,700
Posted By David_Thompson

f1 = bad machine control. call whirlpool and tell...

f1 = bad machine control. call whirlpool and tell them you know this part was recalled and you demand they send you one free of charge
Replies: 2
Views: 1,521
Posted By David_Thompson

if the motor spins it is most likely not the...

if the motor spins it is most likely not the problem. sounds like the control board.....
Replies: 1
Views: 1,406
Posted By David_Thompson

remove vent duct and with a meat thermometer...

remove vent duct and with a meat thermometer measure the exhaust temp. should be at least 150F. if so then the dryer is fine and problem is vent system
Replies: 4
Views: 734
Posted By David_Thompson

not working or now working?

not working or now working?
Replies: 1
Views: 725
Posted By David_Thompson

the blower motors are a known issue for them. try...

the blower motors are a known issue for them. try fixitnow dot com for manuals
Replies: 6
Views: 909
Posted By David_Thompson

screw a 3/4" piece of plywood to the floor JOISTS...

screw a 3/4" piece of plywood to the floor JOISTS under the washer to secure the flooring

i recommend samsung with VRT, LG with TRUE BALANCE or kenmore with VIBRATION GUARD (made by LG)
Replies: 4
Views: 1,425
Posted By David_Thompson

no pugs this is the older "real" maytag style...

no pugs this is the older "real" maytag style with 2 belts.

see if you can find a service manual online for this thing, one for models starting with LAT would work too. i dont have a ton of...
Replies: 4
Views: 1,425
Posted By David_Thompson

the damper pad may be worn out.

the damper pad may be worn out.
Replies: 6
Views: 909
Posted By David_Thompson

dont get a cabrio. if you want H.E. then get a...

dont get a cabrio. if you want H.E. then get a front loader.

those cabrios beat the clothes to death on the bottom and sprinkle the ones on the top. plus the boards go out and the tub bearing like...
Replies: 4
Views: 3,061
Posted By David_Thompson

if the glow bar is heating up but no flame most...

if the glow bar is heating up but no flame most likely need to replace the 2 coils

if no glow bar heat then check the thermal fuse and the glow bar itself.
Replies: 4
Views: 6,617
Posted By David_Thompson

samsung front loaders dont shake nearly as bad...

samsung front loaders dont shake nearly as bad other ones that dont have balance rings.............
Replies: 2
Views: 1,549
Posted By David_Thompson

you have to place the front panel on the top...

you have to place the front panel on the top first, then have someone LIFT THE DRUM while you rotate the panel down into place
Replies: 8
Views: 6,431
Posted By David_Thompson

most of the time when a washer is tripping the...

most of the time when a washer is tripping the breaker its due to stuck contacts in the timer.
Replies: 3
Views: 1,370
Posted By David_Thompson

heater element shorted to ground will do it too....

heater element shorted to ground will do it too. make sure dryer doesnt heat when set to air dry....
Replies: 11
Views: 2,269
Posted By David_Thompson

the drain hose ALWAYS has water in it

the drain hose ALWAYS has water in it
Replies: 11
Views: 2,269
Posted By David_Thompson

the drain hose maybe? may have inner and outer...

the drain hose maybe? may have inner and outer drain hoses. also has a tub to pump hose. still didnt post the model#
Replies: 11
Views: 2,269
Posted By David_Thompson

inside of...

inside of what?.....................................
Replies: 5
Views: 4,441
Posted By David_Thompson

uses the same thermostats on auto and timed. ...

uses the same thermostats on auto and timed.

remove the vent and with your meat thermometer measure the exhaust temp on the various cycles. all should get to at least 150F on high. if it is then...
Replies: 21
Views: 107,723
Posted By David_Thompson

^yes............................................

^yes............................................
Replies: 9
Views: 5,402
Posted By David_Thompson

^ ...

^ .....................................
Showing results 1 to 25 of 200
 


 
Forum Jump