Search: Posts Made By: juanpablo
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 23
Views: 1,617
Posted By juanpablo

Rechecked pressures. Upper valve with pump on at...

Rechecked pressures. Upper valve with pump on at 8 psi, with pump off 11 psi.

Lower valve with pump on at 13 psi, with pump off at 12 psi.

Have attached flow line sketch from water input...
Replies: 23
Views: 1,617
Posted By juanpablo

A previous photo shows position of the lower...

A previous photo shows position of the lower valve, directly under the pump. I'm most certain that line was hot, nonetheless, I'll double check water line routing.

Also, will create a sketch...
Replies: 23
Views: 1,617
Posted By juanpablo

Thank you for your help. Will take a couple...

Thank you for your help.

Will take a couple of days to redo testing.

I'll get a higher rated gauge so as to see what pressures actually are with pump on and off at both upper and lower valves. ...
Replies: 23
Views: 1,617
Posted By juanpablo

Purchased a 0-30 psi gauge and created assembly...

Purchased a 0-30 psi gauge and created assembly that connects to valves.

With pump running attached gauge to each valve.

Attached to upper valve and opened valve slowly. Reading is 12 psi.
...
Replies: 23
Views: 1,617
Posted By juanpablo

NJT, Will take a couple of days to test. ...

NJT,

Will take a couple of days to test. Will forward results.

John
Replies: 23
Views: 1,617
Posted By juanpablo

The gauge has two needles. One shows 22...

The gauge has two needles.

One shows 22 psi. the other reads zero.
Replies: 23
Views: 1,617
Posted By juanpablo

Ok, here goes again......... these are at higher...

Ok, here goes again......... these are at higher resolution

I have attached pictures showing current system. House has a basement with single floor above, no second floor. Estimate sq-ft at...
Replies: 23
Views: 1,617
Posted By juanpablo

NJT: My thread system now shows pictures. ...

NJT:
My thread system now shows pictures. Hopefully this will work.
Thank you,
John
Replies: 23
Views: 1,617
Posted By juanpablo

Trying images again in JPEG format, less than...

Trying images again in JPEG format, less than 50K:

I have attached pictures showing current system. House has a basement with single floor above, no second floor. Estimate sq-ft at 1500.

First...
Replies: 23
Views: 1,617
Posted By juanpablo

I changed files to zip format and resending...

I changed files to zip format and resending thread.

Still, problem with pictures. Awaiting admin help

john
Replies: 23
Views: 1,617
Posted By juanpablo

I have attached pictures showing current system. ...

I have attached pictures showing current system. House has a basement with single floor above, no second floor. Estimate sq-ft at 1500.

First shows the upper valve. Note there are copper pipes...
Replies: 23
Views: 1,617
Posted By juanpablo

Gentlemen, Thank you for the reply, and...

Gentlemen,
Thank you for the reply, and sorry for delay.

I will forward pictures ASAP.

The system does not have any gauges whatsoever. Only an upper valve and lower valve...
Replies: 23
Views: 1,617
Posted By juanpablo

Bleed air from an older design system - with only an upper and lower valve

New to the forum, so please excuse if this has been listed.

My mother-in-law's home was built in 1964 with hot water heating system. Each room has the small radiator fin type heaters, some with...
Showing results 1 to 14 of 14


 
Forum Jump