Search: Posts Made By: 31YTech
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 5
Views: 5,502
Posted By 31YTech

Hello spirittoo, Google "MAINTENANCE KIT"...

Hello spirittoo,


Google "MAINTENANCE KIT" and you will see many, they include air-oil and fuel filters, spark plug and oil. Confirm the air filter in the kit is the correct one.

ereplacement...
Replies: 3
Views: 454
Posted By 31YTech

Hello jogordo, You can purchase 2.0 tips...

Hello jogordo,


You can purchase 2.0 tips in any degree fan you like HERE (http://www.ppe-pressure-washer-parts.com/product/Q1503).....


Good Luck,


31
Replies: 10
Views: 1,164
Posted By 31YTech

Hello layzee, With the float bowl off and...

Hello layzee,

With the float bowl off and holding the carb up side down, is the top of the float parallel with the bowl mating surface of the carb body ?

My guess is the float needle valve seat...
Replies: 15
Views: 909
Posted By 31YTech

Hello BFHFixit, Sounds like you need a...

Hello BFHFixit,

Sounds like you need a bigger hammer, I've popped hundreds of rotors loose with this method. The laws of physics prove this works, I've posted this all over the net and your the...
Replies: 15
Views: 909
Posted By 31YTech

Don't feel stupid BFHFixit, just chalk it up as a...

Don't feel stupid BFHFixit, just chalk it up as a learn'n experience.... ;)

I use to do the crowbar thing until I broke the magnets loose on a Kohler flywheel (glued in), I've been using the PTO...
Replies: 15
Views: 909
Posted By 31YTech

Hello BFHFixit To remove a generator...

Hello BFHFixit


To remove a generator rotor from the engine crankshaft, just loosen the thru bolt. Remove the recoil assembly to gain access to the flywheel nut/bolt, set the correct size socket...
Replies: 9
Views: 490
Posted By 31YTech

Hello kajuk, When a engine is put to...

Hello kajuk,


When a engine is put to rest, fuel left in the carb throat can cause a gummy substance. This can cause the shaft to stick and not react properly when loads are applied. Just...
Replies: 9
Views: 490
Posted By 31YTech

Hello kajuk, This unit has a all gear...

Hello kajuk,


This unit has a all gear driven gearcase, therefore if the belts are tight it will drive the tines.

Two things come to mind, there's gearcase seal protectors on the tines, grass...
Replies: 9
Views: 3,276
Posted By 31YTech

Hello TexasFire, Unless you have a...

Hello TexasFire,


Unless you have a pressure gauge to put in line on the pump, it's best not to try adjusting pressure or pump damage could occur.

Try replacing the tip with a new one first,...
Replies: 4
Views: 376
Posted By 31YTech

Hello Marq1, Work'n for a MTD/Cub dealer,...

Hello Marq1,


Work'n for a MTD/Cub dealer, I haven't seen a commercial WB with a single hydro pump operating both a right and left wheel motor.

If your unit does have two hydro pumps (one for...
Replies: 11
Views: 8,893
Posted By 31YTech

Hello Dave Rischar, Sorry I hadn't gotten...

Hello Dave Rischar,


Sorry I hadn't gotten back sooner, I was off work yesterday.




The magnet poles are different and the flywheel key slot is in a different position.
Replies: 11
Views: 8,893
Posted By 31YTech

Hello Dave Rischar, I knew Kohler offered a...

Hello Dave Rischar,

I knew Kohler offered a ignition "kit" that takes the place of the old SAM ignition system, upon looking up the part number for this kit using a "basic" engine spec. number I...
Replies: 17
Views: 5,222
Posted By 31YTech

Hello BFHFixit, I agree with trying to slide...

Hello BFHFixit,

I agree with trying to slide the first few pickles out, but the analogy I was thinking is when you get down to two/three dills in a large jar, they float on top on their side....
Replies: 17
Views: 5,222
Posted By 31YTech

Hello marbobj, Ha! Must be a younger...

Hello marbobj,


Ha! Must be a younger fella eh ? ;)


31
Replies: 17
Views: 5,222
Posted By 31YTech

Hello jl66redcpe, I suggest changing the...

Hello jl66redcpe,


I suggest changing the oil if there's any hint of fuel smell, if there is it's also thinning the oil out. Just draining down thinned oil could still promote smoking. As you...
Replies: 17
Views: 5,222
Posted By 31YTech

Hello Mr. Cheese, You are correct, that...

Hello Mr. Cheese,


You are correct, that was the first change made trying to solve the blowing gasket issue.

As I recall;

The first design Command engine had head studs with the same...
Replies: 17
Views: 5,222
Posted By 31YTech

Hello jl66redcpe, Could you please look...

Hello jl66redcpe,


Could you please look on the flywheel cover for a white decal, on that decal will be a model and spec. number. Post those numbers up and I'll be happy to look it up for you, I...
Replies: 17
Views: 5,222
Posted By 31YTech

Hello jl66redcpe, Adding to all the great...

Hello jl66redcpe,

Adding to all the great replies to your question, it's possible the head gasket he was sold was old stock of the old design, not the latest greatest design. Make sure the...
Replies: 11
Views: 1,997
Posted By 31YTech

Hello Malcg, I looked up your engine and...

Hello Malcg,


I looked up your engine and saw you have a magneto ignition system with points and condenser, but you still have to have some type switch toggle or another type to shut the engine...
Replies: 11
Views: 1,997
Posted By 31YTech

Hello Malcg, If the engine starts and...

Hello Malcg,


If the engine starts and runs fine your issue isn't with the engine but the welder/generator end of it, the wire from the contact breaker/condenser to the welder is the kill or shut...
Replies: 1
Views: 784
Posted By 31YTech

Hello jackie585858, The high speed RPM is...

Hello jackie585858,


The high speed RPM is adjusted with the phillips screw in the red box below, make sure the governor spring between the lever this screw adjust to the governor arm on top of...
Replies: 3
Views: 806
Posted By 31YTech

Hello Scslattery, Mr Cheese is correct, If...

Hello Scslattery,

Mr Cheese is correct, If you have a multimeter you can perform the following test to assure that is your issue before replacing it. Just choose the one that looks like what's on...
Replies: 7
Views: 2,038
Posted By 31YTech

Hello Garry, After some research (memory...

Hello Garry,

After some research (memory fading) I believe the link with spring goes where the red box's are, with the spring on the governor lever.....

...
Replies: 7
Views: 2,038
Posted By 31YTech

Hello Garry, Can you look on the engine...

Hello Garry,


Can you look on the engine flywheel cover for the model and possibly a spec. number, with that I can see which control assembly you have.....

31
Replies: 17
Views: 3,524
Posted By 31YTech

Hello Jaywalker, Sounds like the classic...

Hello Jaywalker,

Sounds like the classic case of a chunk of carbon build-up breaking loose and getting stuck under one or both valves keeping them from seating, removal of the head and cleaning...
Showing results 1 to 25 of 200
 


 
Forum Jump