Search: Posts Made By: brian44220
Showing results 1 to 25 of 55
Search took 0.01 seconds.
Replies: 9
Views: 713
Posted By brian44220

Those are a little think, if I am looking at the...

Those are a little think, if I am looking at the correct bits they are around 40 bucks a piece. The lead sleeves are cheep at least.
Replies: 9
Views: 713
Posted By brian44220

Any specific brand that you use or know the name...

Any specific brand that you use or know the name of?
Replies: 9
Views: 713
Posted By brian44220

Guess I will go buy some more and get a sharpener...

Guess I will go buy some more and get a sharpener to then.
Replies: 9
Views: 713
Posted By brian44220

Question Drill bit?

So recently bought a Tapcon hammer drill bit with carbide tip for concrete, the guy and homedepot said it would work for what Iím doing, Iím trying to install a latch on the corner of my house...
Replies: 11
Views: 456
Posted By brian44220

Thanks Spott very much appreciated,

Thanks Spott very much appreciated,
Replies: 11
Views: 456
Posted By brian44220

Yes the reset button is incorporated as well as...

Yes the reset button is incorporated as well as what I think is a heat sensor or thermostat, itís about 2 feet long, I havenít figured out how to upload pictures to this website.
Replies: 11
Views: 456
Posted By brian44220

Ok I figured out what’s wrong with my boiler, the...

Ok I figured out what’s wrong with my boiler, the circulation pump isn’t kicking on, Made sure that works by powering it up by applying 120 to it, I hear water circulating, sounds like there is a lot...
Replies: 11
Views: 456
Posted By brian44220

Steamboy It is a radiator based system, no...

Steamboy
It is a radiator based system, no baseboards I believe, the first floor radiators are tucked into the walls so I donít know if thatís considered baseboard, I know what electrical baseboard...
Replies: 11
Views: 456
Posted By brian44220

Unless it used to be oil heated water a long time...

Unless it used to be oil heated water a long time ago, the water heater is right next to the boiler, does the boiler think that the water heater is still running on oil heat?
Replies: 11
Views: 456
Posted By brian44220

Not sure what you mean but domestic water supply,...

Not sure what you mean but domestic water supply, it does not heat my hot water if thatís what you mean, the water heater is full electric.
Replies: 11
Views: 456
Posted By brian44220

Boiler and thermostat not synced?

So my family and I just bought a new home, the boiler works great, but my only issue is when I set the thermostat to 50 or 60 the boiler keeps cycling about every 20 minutes or so for 3 minutes at a...
Replies: 6
Views: 319
Posted By brian44220

Pjmax Donít know what I was thinking, ...

Pjmax
Donít know what I was thinking, silicone spray is best sorry for wrong recommendation.
Replies: 6
Views: 319
Posted By brian44220

Itís called pinch protection, you probably have a...

Itís called pinch protection, you probably have a problem with the window guid binibg causing pinch protection to activate a go back down, either that or the cables on the regulator are coming apart...
Replies: 8
Views: 353
Posted By brian44220

Could use a dial indicator also to check runout.

Could use a dial indicator also to check runout.
Replies: 3
Views: 389
Posted By brian44220

Canít see what your talking about but g35 exhaust...

Canít see what your talking about but g35 exhaust heat shields always brake loose due to rust, you can cut it off or put a big metal band clamp around it.
Replies: 5
Views: 318
Posted By brian44220

Maybe hood a code reader up and see if any faults...

Maybe hood a code reader up and see if any faults are stored. But yes I would check fuel pressure to, spending money and replacing good parts is no good.
Replies: 7
Views: 758
Posted By brian44220

You could spray some power lube or wd40 on the...

You could spray some power lube or wd40 on the joint of the intermediate steering shaft and steer the wheel lock to lock and repeat a couple of times, if you get your steering back then most likely...
Replies: 6
Views: 500
Posted By brian44220

The fault code is in relation to the temperature...

The fault code is in relation to the temperature blend door actuator, you may be able to get to it by removing the glove compartment, you can try to recalibrate the actuators, just remove the M-1...
Replies: 6
Views: 500
Posted By brian44220

One more thing, what size engine does it have?

One more thing, what size engine does it have?
Replies: 6
Views: 500
Posted By brian44220

Whatís you high side reading?

Whatís you high side reading?
Replies: 2
Views: 388
Posted By brian44220

Routan/ Dodge Grand Caravan. Sound like a...

Routan/ Dodge Grand Caravan. Sound like a malfunctioning key remote, if your not pressing any buttons ant this is happening anyway. If you have more then one remote leave the other one in you house...
Replies: 2
Views: 901
Posted By brian44220

Looks like heat shielding for one of the...

Looks like heat shielding for one of the catalytic converters, usually I use a large mettle worm gear clamp or band clamp to reattach those, most people just cut them off. The shields are suppose to...
Replies: 3
Views: 755
Posted By brian44220

Sounds like he wanted to remove the front O2...

Sounds like he wanted to remove the front O2 sensors to fix the check engine light..
Replies: 5
Views: 545
Posted By brian44220

I second what Pjmax said, it should cycle in much...

I second what Pjmax said, it should cycle in much longer intervals so yes your system is still low man. I would have a professional evacuat the system and put the proper amount in along with some...
Replies: 3
Views: 1,103
Posted By brian44220

Vent valve connector has common broken wires that...

Vent valve connector has common broken wires that make contact on and off causing faults to set. I would unplug it and give a tug on each individual wire to see if one is separating. Could be a ecm...
Showing results 1 to 25 of 55
 


 
Forum Jump