Search: Posts Made By: alan73
Showing results 1 to 25 of 200
Search took 0.04 seconds.
Replies: 3
Views: 115
Posted By alan73

both have similar life spans the flooded will...

both have similar life spans the flooded will probably last longer than the AGM but the difference is probably insignificant meaning they both will probably fail a load test at 4-5 years old if they...
Replies: 3
Views: 97
Posted By alan73

installing a remanufactured axle in most cases is...

installing a remanufactured axle in most cases is probably going to cost less if your having a shop do the work labor to r and r the axle, where with replacing the boots you still have r and r axle...
Replies: 30
Views: 462
Posted By alan73

typically install them with the float down all...

typically install them with the float down all the way to the bottom you stick the float part in the tank first and slide it to where the float arm first bend is then you should be able to then...
Replies: 7
Views: 128
Posted By alan73

would probably just use a small air spray gun and...

would probably just use a small air spray gun and primer, paint and clear coat to make it look as good as possible since these are small parts really no reason it should not look good if you take...
Replies: 8
Views: 162
Posted By alan73

would just look at the channels available in your...

would just look at the channels available in your area from one of the sites looks like most are probably uhf but maybe 1 vhf cbs channel 8 if you are having issues with getting that channel and is...
Replies: 5
Views: 745
Posted By alan73

since the original post was in june good chance...

since the original post was in june good chance its already been fixed.
not sure I agree with everything you say but yes if you add dye the system needs to be running and circulating the dye around...
Replies: 7
Views: 128
Posted By alan73

what type of light fixture are you putting up...

what type of light fixture are you putting up exactly sounds like you may of wired it correctly if you had 2 lights of the 4 working, would really look at the new fixture more closely see how its...
Replies: 30
Views: 462
Posted By alan73

fuel pump should of came with clips on this model...

fuel pump should of came with clips on this model there would be a white and black quick release clips holding the gas lines on along with new o ring tank seal.
Replies: 4
Views: 126
Posted By alan73

during construction you probably had many more...

during construction you probably had many more options for insulation that was installed as they attach the corrugated metal now that it is already built would also think spray foam would work the...
Replies: 30
Views: 462
Posted By alan73

if there Is a lot of sediment it could cause...

if there Is a lot of sediment it could cause early failure of the pump but 5-6 years is not to bad also pays to keep the fuel filter changed at regular intervals so it never really plugs up and...
08-07-19, 12:33 PM
Replies: 13
Views: 235
Posted By alan73

being at ground level they may become a problem...

being at ground level they may become a problem using a mower or weed eater or anything that makes much noise very close to the entrance.
Replies: 16
Views: 550
Posted By alan73

capacity is usually on a sticker under the hood,...

capacity is usually on a sticker under the hood, its going to be the same no matter what temp it is.
Replies: 16
Views: 550
Posted By alan73

did you pull a vacuum on the system prior to...

did you pull a vacuum on the system prior to filling.
did you purge air from the manifold lines and fill the system to capacity?
Replies: 7
Views: 239
Posted By alan73

looks like a mechanical temp gauge so you would...

looks like a mechanical temp gauge so you would change everything sender and gauge if you ever need to replace it.
08-04-19, 04:22 PM
Replies: 9
Views: 218
Posted By alan73

would just use the information provided to know...

would just use the information provided to know the amp draw otherwise you could probably use an amp meter on it and see how much current is being used during operation a lot of multi meters can...
Replies: 8
Views: 284
Posted By alan73

what type of tractor is it? would probably just...

what type of tractor is it?
would probably just run it since you have it running see how long the points last in it , good chance you will get decent life out of them since tractors are not used as...
Replies: 8
Views: 284
Posted By alan73

your input voltage seems a little low you...

your input voltage seems a little low you sometimes lose a little through the ignition switch but 11.2 is a bit low.
a lot of cars had circuits that gave the resistor full battery voltage in the...
Replies: 5
Views: 232
Posted By alan73

would probably just replace both rear calipers...

would probably just replace both rear calipers including rotors if it needs them.
Replies: 9
Views: 521
Posted By alan73

wasnt the light already on a switch? this is the...

wasnt the light already on a switch? this is the one you just want to move away from a/c duct?
07-23-19, 06:51 AM
Replies: 7
Views: 399
Posted By alan73

probably less resistance to move it with the 4...

probably less resistance to move it with the 4 inch side down, but it will be very hard to move due to its weight so not sure how important that is for you if you did ever try dragging it on the...
07-23-19, 12:37 AM
Replies: 2
Views: 227
Posted By alan73

since it has a battery it would have an energy...

since it has a battery it would have an energy source but it would probably be hard to do on a small scale water wheels turn slow you would have to speed up the output of the wheel to really get any...
07-22-19, 08:44 AM
Replies: 17
Views: 528
Posted By alan73

probably dont have much choice other than...

probably dont have much choice other than drilling it to 1/4 inch if your going to try to make it work, you can buy longer bolts with a shoulder ,1/4 inch clevis or wire lock pins are common in 1/4 ...
07-21-19, 05:03 PM
Replies: 17
Views: 528
Posted By alan73

need to probably increase the thickness would...

need to probably increase the thickness would drill a larger hole then can probably get by with a bolt or pin that is thicker in size
Replies: 14
Views: 383
Posted By alan73

probably could use some jumper wires hook up your...

probably could use some jumper wires hook up your ground and then apply power to each terminal. they do make testers with a power supply but they are expensive probably not worth the cost you could...
Replies: 12
Views: 546
Posted By alan73

you could also check wires with a ohm meter but...

you could also check wires with a ohm meter but since there is varying resistance values do to different suppression core materials would suspect any wire with less than 10k per foot is likely good...
Showing results 1 to 25 of 200
 


 
Forum Jump