Search: Posts Made By: geotechnical
Showing results 1 to 19 of 19
Search took 0.01 seconds.
11-23-07, 07:14 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Left jumper in place. Yes there is a ground from...

Left jumper in place. Yes there is a ground from module to pilot. The flame is about 2 inches high.
11-20-07, 05:10 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Don't see a second sensor

Don't see a second sensor
11-19-07, 07:00 PM
Replies: 43
Views: 5,889
Posted By geotechnical

As far as I can tell the connections are good

As far as I can tell the connections are good
11-19-07, 06:22 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Something is clicking, yes, when the pilot is...

Something is clicking, yes, when the pilot is lit. Just went to check it out again, and the burner lit for a few seconds, shut off, but the pilot stayed on and clicking continued for a few seconds,...
11-19-07, 05:57 PM
Replies: 43
Views: 5,889
Posted By geotechnical

I believe so. There is a small blue flame when I...

I believe so. There is a small blue flame when I turn on the power every time. Then the control clicks for a while, then the flame turns off and the control flashes that it is in recycle mode.
11-19-07, 05:26 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Good Evening... Furnace was off all day,...

Good Evening...

Furnace was off all day, came home and turned on power, burner lit for a few seconds then control went into recycle mode and burner never lit again. Tried turning power off then...
11-18-07, 06:27 PM
Replies: 43
Views: 5,889
Posted By geotechnical

OK...I can see the bottom of it, but not the top,...

OK...I can see the bottom of it, but not the top, it is obstructed by other parts, but from where I can see the flame is, it should definitely be reaching it. I can access the two screws on the...
11-18-07, 05:05 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Model No. is 867.767031 I either can't...

Model No. is 867.767031

I either can't really see the flame sensor rod or there isn't one? I can't see the lower portion of the flame but it is about 3 inches high and I can see all of the area...
11-18-07, 02:15 PM
Replies: 43
Views: 5,889
Posted By geotechnical

I'm not entirely sure what either of those are. ...

I'm not entirely sure what either of those are. I think the sensing rod is part of the ignitor and doesn't seem to be easily accessible. Have found pics of air proving switchs online and don't see...
11-18-07, 12:49 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Well that worked a little, at least the module is...

Well that worked a little, at least the module is responding. But same problem as with old one, it clicks for a while, sometimes lights, sometimes doesn't, but no heat ever comes out.
11-18-07, 06:21 AM
Replies: 43
Views: 5,889
Posted By geotechnical

Please bear with me in my descriptions... ...

Please bear with me in my descriptions...

Kenmore 867.76703 furnace

PV, MV/PV, and MV are label on furnace and corresponding wires went to corresponding locations on module

green ground wire...
11-18-07, 05:49 AM
Replies: 1
Views: 2,838
Posted By geotechnical

Replacing Honeywell S8610H1038 with Johnson G779LHA-1

Have followed Figure 3 in manual, with the exception that there was no thermostat wire going into previous control, so I have none to go into new control. Fan will turn on but nothing else.
11-18-07, 05:35 AM
Replies: 43
Views: 5,889
Posted By geotechnical

It wasn't working properly. Last year it would...

It wasn't working properly. Last year it would turn on after repeatedly messing with the thermostat, of and on over and over, then it would kick in. This year it seems I have to actually turn off...
11-17-07, 07:27 PM
Replies: 43
Views: 5,889
Posted By geotechnical

There was no wire there on the old one

There was no wire there on the old one
11-17-07, 07:13 PM
Replies: 43
Views: 5,889
Posted By geotechnical

yes, but there is no wire going to THS 2. there...

yes, but there is no wire going to THS 2. there wasn't one for the honeywell.
11-17-07, 06:57 PM
Replies: 43
Views: 5,889
Posted By geotechnical

The fan does work

The fan does work
11-17-07, 05:46 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Just dead. The manual says fig 3 or 4 for...

Just dead. The manual says fig 3 or 4 for replacing Honeywell S8610H, which seems to match the original wiring. Sorry, don't know too much about this, but figured it would work since they said it...
11-17-07, 05:35 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Could not afford the installation fee and this...

Could not afford the installation fee and this was the part they recommended and they said it would be easy to replace. I think it is wired correctly, but nothing happens when I turn the power on.
11-17-07, 04:38 PM
Replies: 43
Views: 5,889
Posted By geotechnical

Unhappy Replacing Intermittent Pilot Ignition Control

I currently have a Honeywell S8610H1038. A service tech said this need replacing and I have purchased a Johnson Controls G779LHA-1.

The Honeywell has MV, PV, and MV/PV wires, but there is not a...
Showing results 1 to 19 of 19


 
Forum Jump