Search: Posts Made By: bambiblaster
Showing results 1 to 25 of 200
Search took 0.04 seconds.
Replies: 6
Views: 2,294
Posted By bambiblaster

Did you ever let it run till the end on its own...

Did you ever let it run till the end on its own and if so did it dry the dishes,, If did no dry there is a heater problem not keeping the water hot. There should be a tech diagnose sheet behind the...
Replies: 2
Views: 868
Posted By bambiblaster

Tks Roger... New battery and turns freely.. just...

Tks Roger... New battery and turns freely.. just talked to a lg tech and he comfirmed what I thought.. compression release on cam is worn. He has run into this on the 18.5 Briggs often..
Replies: 2
Views: 868
Posted By bambiblaster

Tractor starter

Have a B&S engine on a Craftsman Lawn Tractor. The starter magnets came loose in starter so I purchased another starter now this starter worked for 2 weeks now it is not working. Turns freely but...
Replies: 1
Views: 613
Posted By bambiblaster

If its a older fridgidaire the boot is a update...

If its a older fridgidaire the boot is a update kit and comes with instructions... Dont know which you have I see you left no model number
Replies: 1
Views: 993
Posted By bambiblaster

Sounds like the cycle speed selector switch is...

Sounds like the cycle speed selector switch is stuck in a gentle setting... The wiring diagram in the console will show what contacts on that switch to test are..
Replies: 1
Views: 881
Posted By bambiblaster

Can you just build a shelf to slide the dryer...

Can you just build a shelf to slide the dryer onto above the washer ... also look at yours goto a diff store and look for yourself and see if they match... i thought they fit unless yours is really...
Replies: 9
Views: 4,179
Posted By bambiblaster

Unplug and open console there is a tech sheet on...

Unplug and open console there is a tech sheet on tests for this maching.... also you can tip it back unplug motor electrical connection and reinsert and try...
Replies: 1
Views: 2,448
Posted By bambiblaster

Should be 3.1.........

Should be 3.1.........
Replies: 8
Views: 4,831
Posted By bambiblaster

Had one of there the other day,, The control...

Had one of there the other day,, The control board relay was fried... had to put in a new control...
Replies: 8
Views: 4,831
Posted By bambiblaster

Can you get the model number from inside door......

Can you get the model number from inside door... there could be a few different problems depending on model
Replies: 6
Views: 1,528
Posted By bambiblaster

Yes should be the timer... On the sudden stop...

Yes should be the timer... On the sudden stop "dont put oil or any lube on the clutch" this will make it slip in the spin cycle.. the clutch releases the brake which is also what drives the basket...
Replies: 2
Views: 1,661
Posted By bambiblaster

You will be needing rear drum/bearing and most...

You will be needing rear drum/bearing and most likely the spin basket... There are alot of post in here about the front loader rear bearing.. just a matter of tackling it and the costs
Replies: 5
Views: 9,917
Posted By bambiblaster

I would replace the heater housing therma fuse as...

I would replace the heater housing therma fuse as well...Especilly with that much shorting goin on,...


Dave,

Something aint it... I ve run accross alot of those..

Sane with dishwashers...
Replies: 2
Views: 934
Posted By bambiblaster

Yes there shoukd be a spring too.. remove the...

Yes there shoukd be a spring too.. remove the door hinge screws and the 2 on the otherside will give you acess to the inside...you can pull the boot off the inner door, it just presss in,, here is...
Replies: 5
Views: 9,917
Posted By bambiblaster

From what i gather so far you removed the three...

From what i gather so far you removed the three screws in the back of drum.. You should have removed belt and reached in drum and hit it hard upward in the rear to knock out the ball in the soccket...
Replies: 2
Views: 3,117
Posted By bambiblaster

Here is step by step to disasseble yours ...

Here is step by step to disasseble yours


http://www.applianceaid.com/wpdryer_how-to.html

Pics

http://www.applianceaid.com/slidewpdry.html
Replies: 5
Views: 3,807
Posted By bambiblaster

Sears has the motor for 183.00 pt # 27658P...

Sears has the motor for 183.00 pt # 27658P...
Replies: 12
Views: 16,980
Posted By bambiblaster

Very bottom of the front there are 3 screws...

Very bottom of the front there are 3 screws (torx) remove them lower panel comes off... on right side is the tech sheet... if you reach your hand strait up from inside below the door switch there is...
Replies: 12
Views: 16,980
Posted By bambiblaster

Remove the ower panel the tech sheet is there and...

Remove the ower panel the tech sheet is there and lists all code and tests
Replies: 4
Views: 1,015
Posted By bambiblaster

In reference to the original posting that site I...

In reference to the original posting that site I gave you has other info on the bearing and other possible shaking issues..


http://www.servicematters.com/maytag_library/html/index.html
Replies: 6
Views: 11,332
Posted By bambiblaster

There are a couple of issues you could be...

There are a couple of issues you could be having...

1. A bad motor relay in the console..

2. Bad even heat board..

Here is a link to test this dryer...
...
Replies: 1
Views: 661
Posted By bambiblaster

Try some disposer cleaner and run it... most...

Try some disposer cleaner and run it... most likely the renters have put everything in there to include oil and greese...And there is also a possible drain pipe problem
Replies: 4
Views: 4,867
Posted By bambiblaster

Usually caused by a loose connection... seen it a...

Usually caused by a loose connection... seen it a few times but not too often,,,,
Replies: 4
Views: 4,867
Posted By bambiblaster

Usually caused by a loose connection... seen it a...

Usually caused by a loose connection... seen it a few times but not too often,,,,
Replies: 1
Views: 1,561
Posted By bambiblaster

Remove the 2 lower screws on te panel to look...

Remove the 2 lower screws on te panel to look from bottom and also remove 4 screws from rear of top to remove it and look...
Showing results 1 to 25 of 200
 


 
Forum Jump