Search: Posts Made By: GregH
Showing results 1 to 25 of 200
Search took 0.05 seconds.
08-09-19, 06:58 PM
Replies: 3
Views: 148
Posted By GregH

If the stem was at the bottom when you added air...

If the stem was at the bottom when you added air and you did not hear gurgling then there is likely no fluid in it,
Do you know that for sure that they are fluid filled?

Put the stem at the...
Replies: 8
Views: 243
Posted By GregH

It is not recommended to reduce a vehicle battery...

It is not recommended to reduce a vehicle battery to below 10 volts as its life will be shortened.
To take it to a few volts or even zero volts will do damage and it might work if you bring it back...
Replies: 16
Views: 357
Posted By GregH

The fuel level on my riding mower is also...

The fuel level on my riding mower is also difficult to see.
Knowing rougly how much fuel it uses and keeping the tank full has so far prevented running outta gas.
Replies: 7
Views: 247
Posted By GregH

How does the engine run after this modification? ...

How does the engine run after this modification?
Fuel injected engines will normally use engine temperature to adjust fuel and timing settings.
08-04-19, 07:53 AM
Replies: 1
Views: 176
Posted By GregH

Welcome to our forums!

This is an installation that requires a permit and whoever grants it will advise on what components are ok to use.

The hook-up aside there are a few things you will need to address.
The gas...
07-31-19, 04:04 AM
Replies: 12
Views: 385
Posted By GregH

I am not sure what your thinking is that...

I am not sure what your thinking is that replacing an electric furnace would change the cost to heat your home.
Electric heat is 100% efficient and the size of the furnace has no impact on...
07-31-19, 03:35 AM
Replies: 2
Views: 231
Posted By GregH

Thumbs up Welcome to our forums!

It is uncommon for a residential ac unit to have a start capacitor.
To have a start capacitor would mean that there would have to be a start relay which is a cost most companies don't want to add. ...
Replies: 6
Views: 265
Posted By GregH

It is normal for a chisel head to deform...

It is normal for a chisel head to deform slightly.
Touch it up on a grinder.
Replies: 8
Views: 350
Posted By GregH

Does the pump deliver 3 gpm @ 300' lift or is...

Does the pump deliver 3 gpm @ 300' lift or is that delivery spec at a lesser lift/static pressure?
Also, how deep is the water level in the casing?
Replies: 8
Views: 350
Posted By GregH

Thumbs up Welcome to our forums!

Yes, you will need something more powerful than a small DC pump.
It takes a fair amount of power to lift the water from the level that your well is at.

You need a different approach.
A small...
Forum: Water Heaters
07-26-19, 02:31 AM
Replies: 2
Views: 272
Posted By GregH

In order to propertly diagnose this you would...

In order to propertly diagnose this you would need to install a pressure gauge in the cold water line at the hw tank.
You are only guessing that the restriction is at the check valve and would need...
07-18-19, 05:54 AM
Replies: 12
Views: 546
Posted By GregH

Ya, There is a cost for anything you want or...

Ya,
There is a cost for anything you want or need.
As opposed to just buying something there is a cost in the time to learn a skill , the cost of tools and the cost of material to DIY.
The better...
07-18-19, 03:46 AM
Replies: 4
Views: 348
Posted By GregH

Based on your description it sounds like the fan...

Based on your description it sounds like the fan bearings are worn out.
Unfortunately the availability and cost of parts do not make this a worthwhile repair.
Also, many of these units are...
Replies: 7
Views: 557
Posted By GregH

Marq's method would be the best option IMO. I...

Marq's method would be the best option IMO.
I would suggest using smaller diameter holes.

Draw the outline of the hole you need and drill several holes with a concrete bit and drill.along the...
Replies: 5
Views: 388
Posted By GregH

To my knowledge no such thing exists. A...

To my knowledge no such thing exists.
A carbonator motor is fairly specialized and in addition to the slotted shaft it will have a raised collar on the shaft end to attach the pump.
There is no...
07-13-19, 05:36 PM
Replies: 12
Views: 546
Posted By GregH

I use those furniture blind nuts that pilot shows...

I use those furniture blind nuts that pilot shows to make tripod adapters for security cameras.
You can use a forstner or spade bit on one side of a disk of 1/2" plywood deep enough to make the...
07-07-19, 06:02 AM
Replies: 4
Views: 512
Posted By GregH

Bungee cords or if you wanted to use zip ties you...

Bungee cords or if you wanted to use zip ties you could tie string, rope or wire in a loop just short of the span then attach a shorter zip tie to secure it.
07-07-19, 05:51 AM
Replies: 4
Views: 481
Posted By GregH

Many commercial door closers have two different...

Many commercial door closers have two different close speed adjustments......swing and final close.
The adjustments allow the door to have a faster swing throughout the arc and then slow down for...
Replies: 4
Views: 643
Posted By GregH

The symptoms you describe lead me to believe your...

The symptoms you describe lead me to believe your pneumatic tank is either waterlogged.or the check valve is leaking.
Presumably the "rubbers at the bottom of the pipe" are for the check valve and...
Replies: 6
Views: 621
Posted By GregH

I am unsure of what is standard practice in your...

I am unsure of what is standard practice in your area but here inline fans are not normally used to supply or boost air volume.
They are normally used as an attempt to fix a poor or inadequate duct...
Replies: 18
Views: 710
Posted By GregH

https://shop.harborfreight.com/media/catalog/produ...

https://shop.harborfreight.com/media/catalog/product/cache/1/image/9df78eab33525d08d6e5fb8d27136e95/6/2/62593_zzz_500.jpg
A bearing separator...
Replies: 18
Views: 710
Posted By GregH

I would suggest you move the bearing back if you...

I would suggest you move the bearing back if you can then clean and polish the shaft.
The dirt, rust and small nicks and scratches will add a lot to the thickness of the shaft.
A bearing separator...
Replies: 18
Views: 710
Posted By GregH

Are you sure your bearing is exactly the same as...

Are you sure your bearing is exactly the same as the one in the link?
I can't quite tell by your pics but is the section with the set screws a cam lock type.
You can tell that type by there being...
06-22-19, 08:45 AM
Replies: 4
Views: 421
Posted By GregH

You would need to check and fine tune for local...

You would need to check and fine tune for local HVAC requirements in your trailer but the numbers are fairly universal and vary based on what you are doing.
.
Regardless of the use you would...
Showing results 1 to 25 of 200
 


 
Forum Jump