Search: Posts Made By: Hello
Showing results 1 to 25 of 60
Search took 0.02 seconds.
Replies: 12
Views: 11,611
Posted By Hello

Sounds like you may have a gauge made for a 24"...

Sounds like you may have a gauge made for a 24" tank in a 48" tank?
Replies: 17
Views: 4,449
Posted By Hello

AquaSmart wiring

Hello all

I work for Beckett and had some input into the wiring book. I would have linked to it but our website is down right now.

In a nutshell, using the wiring diagram we have developed...
Replies: 29
Views: 4,302
Posted By Hello

You have to use DHW priority because if the...

You have to use DHW priority because if the indirect calls for the burner to run as a heating call and the outside air temp is over the high temp for the curve then you will try to heat the indirect...
Replies: 29
Views: 4,302
Posted By Hello

Dhw

Sure it does - how could you do ODR without it?
Replies: 29
Views: 4,302
Posted By Hello

Why not just use the Beckett Aquasmart with...

Why not just use the Beckett Aquasmart with wireless outdoor temp reset and be done with it. it will cost less and it is standard equipment on that boiler now.
Replies: 5
Views: 1,053
Posted By Hello

Jump out T-T ...

Jump out T-T .
Replies: 7
Views: 1,783
Posted By Hello

No You have a outdoor reset control, that...

No

You have a outdoor reset control, that should take care of the heat...If the wife complains just boost the indirect temp a bit.
Replies: 7
Views: 1,783
Posted By Hello

The aquastat for the indirect on a Buderus has an...

The aquastat for the indirect on a Buderus has an adjustable differential I belive. I recently changed to an adjustable differential on my indirect because the indirect would bring on the boiler too...
04-07-08, 05:22 AM
Replies: 8
Views: 1,430
Posted By Hello

The L8024 and sometimes L8124 Honeywell aquastats...

The L8024 and sometimes L8124 Honeywell aquastats are prone to arc through the contacts for a whole bunch of seconds prior to them making and upsetting all kinds of electronics during this arcing. ...
Replies: 16
Views: 2,437
Posted By Hello

Not all installations will do this, it has to do...

Not all installations will do this, it has to do with chimney capacity. If there is no draft regulator installed then this may not be fixable. There would be nothing wrong with it just have to...
Replies: 16
Views: 2,437
Posted By Hello

This "thud" is very typical of burners with...

This "thud" is very typical of burners with pre-purge, it is the rapid expansion of combustion gases at startup. If you hold the draft regulator open during startup you may see that it goes away,...
Replies: 74
Views: 12,260
Posted By Hello

Sid Harveys used to have these in the catalog,...

Sid Harveys used to have these in the catalog, check with them
11-09-07, 12:24 PM
Replies: 6
Views: 1,324
Posted By Hello

The newer burner motors with ball bearings and...

The newer burner motors with ball bearings and capacitor, defiantly change the volume and pressure of air to the flame, the burner should be set up by a tech.
06-22-07, 10:20 AM
Replies: 3
Views: 1,086
Posted By Hello

Its a foreclosure, just tell them you want...

Its a foreclosure, just tell them you want another $8000 off in case you need to replace the heating system, they should respond that it is as is, orrrr they may just make sure it works.
Replies: 20
Views: 29,093
Posted By Hello

Read This ...

Read This
http://www.wmur.com/news/10779050/detail.html#
03-26-07, 02:39 PM
Replies: 4
Views: 2,942
Posted By Hello

You said no one in you're area services them,...

You said no one in you're area services them, where are you?
Replies: 2
Views: 762
Posted By Hello

I take it the installer cannot figure it out?

I take it the installer cannot figure it out?
Replies: 12
Views: 2,102
Posted By Hello

If you had a 1967 car would you replace it if it...

If you had a 1967 car would you replace it if it were running OK?
01-13-07, 09:44 AM
Replies: 4
Views: 1,404
Posted By Hello

That would be the wrong control

That would be the wrong control
01-11-07, 09:01 AM
Replies: 4
Views: 1,404
Posted By Hello

The Beckett parts are warenteed for 5 years. The...

The Beckett parts are warenteed for 5 years. The R8184P does have the reqiured pre-purge for the Clencut pump it does not however have interupted ignition. The vast majority of primary controls are...
01-06-07, 01:05 PM
Replies: 7
Views: 860
Posted By Hello

Sorry bodhisatva, I thought you were the guy who...

Sorry bodhisatva, I thought you were the guy who started the thread. Do you have oil dripping?
01-06-07, 01:00 PM
Replies: 7
Views: 860
Posted By Hello

So what you really ment to say is that you have...

So what you really ment to say is that you have oil dripping out of the bottom of the burner housing?
01-06-07, 04:42 AM
Replies: 12
Views: 3,650
Posted By Hello

Removed off topic post.

Removed off topic post.
Replies: 5
Views: 7,562
Posted By Hello

The R7184 control seeks out a cad cell signal at...

The R7184 control seeks out a cad cell signal at 8 seconds into pre-purge if it detects a flame it will lock the burner out. The V4064 delay valve has a very inconsistent delay timing, but most...
Replies: 9
Views: 4,893
Posted By Hello

The following is from the following website: ...

The following is from the following website:

http://beckettadditives.com/heating-oil-additive.asp

Today’s catalytically cracked #2 fuel oil generates solids at an accelerated rate causing a...
Showing results 1 to 25 of 60
 


 
Forum Jump