Search: Posts Made By: Random1
Showing results 1 to 25 of 33
Search took 0.01 seconds.
07-11-19, 06:10 PM
Replies: 7
Views: 320
Posted By Random1

It's not a lighted switch. Just a basic switch. ...

It's not a lighted switch. Just a basic switch.

I'm not sure what your suggesting.



I can try this tomorrow. But I assume nothing would happen. The light wouldn't have any power going to it.
07-11-19, 01:47 PM
Replies: 7
Views: 320
Posted By Random1

Sorry, I will try to be more clear. Each...

Sorry, I will try to be more clear.

Each line was split to run in 2 different directions. One hot+neutral to the gfci and one hot+neutral to the switch.

The gfci side is working good.

On...
07-11-19, 08:59 AM
Replies: 7
Views: 320
Posted By Random1

I split the hot and neutral in the junction box....

I split the hot and neutral in the junction box. One "leg" of the split goes to the gfci then to an outside light. The other "leg" of the split goes to the single pole switch that controls the inside...
07-11-19, 08:37 AM
Replies: 7
Views: 320
Posted By Random1

Garage wiring problems

I decided to rewire my garage. I cut out all the old wire and replaced the old wire, boxes, and receptacles.

Coming into the garage are 2 hot 1 neutral and 1 ground wire. I capped and taped off...
Replies: 9
Views: 479
Posted By Random1

Thanks for the help! I bought a moen single hole...

Thanks for the help! I bought a moen single hole faucet and installed it last night.
Replies: 9
Views: 479
Posted By Random1

I can't take a picture right now, but I don't...

I can't take a picture right now, but I don't believe it's a bathroom faucet. It has a long swivel spout on it. Best guess is the sink is cast iron from the 1940s.
Replies: 9
Views: 479
Posted By Random1

No idea what brand. Some details on the faucet....

No idea what brand. Some details on the faucet. It is deck mounted. 6"centers. It has 3 holes. Supply lines come up the the handles on each side. Middle hole has a line running to the sprayer.
Replies: 9
Views: 479
Posted By Random1

6 inch faucet

I have a kitchen faucet that leaks from the cold water side. I have replaced the cartridge and the seating ring. It works for about a month then starts leaking again. I fear I'll have to replace...
10-14-16, 02:10 PM
Replies: 7
Views: 496
Posted By Random1

Thanks for the help guys! Got the new board...

Thanks for the help guys! Got the new board mounted and installed. Ran system test and everything looked good. Replaced the access panels and turned up the heat. Fired right up! My wife is very...
10-14-16, 12:23 PM
Replies: 7
Views: 496
Posted By Random1

I took off the old board and sure enough there...

I took off the old board and sure enough there was a big burned out spot on the back. Took a bit of searching but I found a supply house that would sell me the board. Most here only sell to the...
10-13-16, 04:16 PM
Replies: 7
Views: 496
Posted By Random1

Hi PJMAX! Thanks for the quick reply. The...

Hi PJMAX! Thanks for the quick reply.

The motor was definitely bad. I can see the burnt windings. Could the motor have ruined the board or visa verse? I guess it doesn't matter. It will have to...
10-13-16, 03:16 PM
Replies: 7
Views: 496
Posted By Random1

Replaced blower still won't start

Carrier gas furnace model 58yav091-14
Installed 12/99
My blower motor burned out. I replaced it with an after market from Dayton. I also replaced the capacitor.
When I call for heat the inducer...
12-22-15, 04:34 PM
Replies: 36
Views: 1,070
Posted By Random1

I still have it. It would be good to have a...

I still have it. It would be good to have a spare. Thanks again guys.
12-22-15, 02:55 PM
Replies: 36
Views: 1,070
Posted By Random1

OK, so I got a call from the supplier saying my...

OK, so I got a call from the supplier saying my parts were in. Picked them up and installed them this afternoon. Took the furnace through a heating cycle, and everything worked beautifully! P Jmax...
12-22-15, 06:10 AM
Replies: 36
Views: 1,070
Posted By Random1

Of course the parts have to be ordered. Should be...

Of course the parts have to be ordered. Should be in Christmas eve.
12-22-15, 01:52 AM
Replies: 36
Views: 1,070
Posted By Random1

OK, I've got those numbers. Thank you for all the...

OK, I've got those numbers. Thank you for all the help! I'll update after the install and let you know how it goes.
12-22-15, 01:33 AM
Replies: 36
Views: 1,070
Posted By Random1

Model and serial number of the furnace? Or of the...

Model and serial number of the furnace? Or of the parts? If those numbers aren't on the parts I'm not sure where to find them.
12-22-15, 01:26 AM
Replies: 36
Views: 1,070
Posted By Random1

I checked the motor for continuity and it showed...

I checked the motor for continuity and it showed non. I rechecked the board for voltage and nothing there either.
12-21-15, 05:09 PM
Replies: 36
Views: 1,070
Posted By Random1

So I guess the next step is the replace both the...

So I guess the next step is the replace both the motor and the control board? Should I remove them and bring the parts with me to the supply house?
12-21-15, 12:10 PM
Replies: 36
Views: 1,070
Posted By Random1

I bought a a different meter. This one's a GE. I...

I bought a a different meter. This one's a GE. I believe I tested everything correctly this time. I may have been the reason the old one is broken. I also unplugged the leads from the board and...
12-21-15, 08:42 AM
Replies: 36
Views: 1,070
Posted By Random1

So I guess the next step is the replace both the...

So I guess the next step is the replace both the motor and the control board? Should I remove them and bring the parts with me to the supply house?
12-21-15, 06:07 AM
Replies: 36
Views: 1,070
Posted By Random1

OK I'm back at it. Thank you for the help so far....

OK I'm back at it. Thank you for the help so far. I bought a new multimeter. When i cross the leads I get .03 reading. When I touch the motor contacts It reads 1. So from what you said that means the...
12-20-15, 01:42 PM
Replies: 36
Views: 1,070
Posted By Random1

Ugh...I have to go to work again now. I think...

Ugh...I have to go to work again now. I think I'll go out in the morning and buy a new meter. Hopefully I can get this fixed tomorrow. Thankfully its not typical December weather here in Buffalo.
12-20-15, 01:35 PM
Replies: 36
Views: 1,070
Posted By Random1

I tried that with the red and black leads and...

I tried that with the red and black leads and still reading -1.
12-20-15, 01:19 PM
Replies: 36
Views: 1,070
Posted By Random1

New battery installed and the meter still reads 1...

New battery installed and the meter still reads 1 when I cross the leads. I think I need a new meter.
Showing results 1 to 25 of 33
 


 
Forum Jump