Search: Posts Made By: BFHFixit
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 49
Views: 1,704
Posted By BFHFixit

As cheese said if your belt goes around the...

As cheese said if your belt goes around the shaft, then it has to be removed to replace the belt.
Replies: 24
Views: 627
Posted By BFHFixit

You should have two wires to a plug for the...

You should have two wires to a plug for the solenoid. Remove it, plug it in and turn on the key. Does it retract? click? or measure for voltage on the plug. Many times the plunger gets gummed up and...
Replies: 49
Views: 1,704
Posted By BFHFixit

That pulley should come off but might be stuck. A...

That pulley should come off but might be stuck. A work around is to remove the 4 engine mounting bolts and slide the engine toward the firewall/steering console. This should give you enough room to...
Replies: 5
Views: 351
Posted By BFHFixit

The seat switch has nothing to do with the...

The seat switch has nothing to do with the starting circuit. Only the brake and the PTO.
IE: You can sit in the seat and not be able to start unless the brake is pushed and working, with the brake...
Replies: 24
Views: 627
Posted By BFHFixit

Bad day at work, my apologies I deal with an...

Bad day at work, my apologies I deal with an idiot all day, my comment was not directed at you davis

What cheese said, when you said past the carb, I wasn't sure you had the carb removed and ........
Replies: 24
Views: 627
Posted By BFHFixit

Welcome to the forum davis_lsu, Do you...

Welcome to the forum davis_lsu,


Do you have a fuel solenoid?

When you pull the spark plug, note the condition, is it wet? oil or fuel, black? carbon or oil..?

When you say you sprayed past...
Replies: 7
Views: 390
Posted By BFHFixit

The torque is going to depend on the size of the...

The torque is going to depend on the size of the bolt so will be different for different machines.
In this case too tight is not a bad thing but it is possible to over torque a bolt and weaken it.
Replies: 49
Views: 1,704
Posted By BFHFixit

K46 means nothing to me????????????? If it is a...

K46 means nothing to me?????????????
If it is a Hydro tranny the input shaft is the pulley that is driven by the drive belt. As for purging, lift and support the mower so the rear wheels are off the...
Replies: 10
Views: 551
Posted By BFHFixit

The air filter covers the throat. Remove the air...

The air filter covers the throat. Remove the air filter then look into the throat while pumping the primer....
Replies: 5
Views: 313
Posted By BFHFixit

It is a locking nut. If your blade is loose on...

It is a locking nut. If your blade is loose on the spindle, about only an impact and holding the pulley will get it off.
Replies: 3
Views: 2,026
Posted By BFHFixit

While you have the plug out next time it dies,...

While you have the plug out next time it dies, check for spark.
Replies: 2
Views: 605
Posted By BFHFixit

You should have a fuel valve. Check your oil for...

You should have a fuel valve. Check your oil for over full and smell of gas. Pull the spark plug and pull it over and watch for fluid being expelled.
If any or all the above, I agree the float valve...
Replies: 43
Views: 2,101
Posted By BFHFixit

:coffee: This is getting good :Wink: ...

:coffee:

This is getting good :Wink:

https://assets.doityourself.com/forum/avatars/cheese.gif
Replies: 3
Views: 2,026
Posted By BFHFixit

Pull the spark plug and see if it cranks. Put a...

Pull the spark plug and see if it cranks. Put a rag or some such over the plug hole and keep the plug wire away. See if your oil level is over full and smells like gas.
Also what is this engine on?...
Replies: 11
Views: 510
Posted By BFHFixit

LOL you will not have points on that engine, the...

LOL you will not have points on that engine, the spark plug creates the spark, the flywheel magnet and magneto produce the voltage for the spark plug to produce spark ;)
There is no coil under the...
Replies: 11
Views: 510
Posted By BFHFixit

When it won't start, check for spark....

When it won't start, check for spark. magneto/coil is the ignition and symptoms especially on briggs of one going bad is loosing spark when they get warm.
Replies: 11
Views: 510
Posted By BFHFixit

Magneto is a possibility...???

Magneto is a possibility...???
Replies: 4
Views: 340
Posted By BFHFixit

When you adjusted the H, how did you adjust it?...

When you adjusted the H, how did you adjust it? If you got it set too lean and then ran it, you may have toasted the cylinder. You can remove the muffler and look in the cylinder and piston for...
Replies: 43
Views: 2,101
Posted By BFHFixit

:facepalm: Good Luck guys!

:facepalm:
Good Luck guys!
Replies: 43
Views: 2,101
Posted By BFHFixit

It depends on what tranny you have and how it...

It depends on what tranny you have and how it shifts...when the drive lever/pedal or whatever is in neutral, it should detent on a switch. Maybe under the fender..?

The brake switch is working...
Replies: 1
Views: 269
Posted By BFHFixit

Most likely the needle/float valve is leaking.

Most likely the needle/float valve is leaking.
Replies: 43
Views: 2,101
Posted By BFHFixit

The PTO and Brake switch are in the starting...

The PTO and Brake switch are in the starting safety circuit. The PTO is also in the kill circuit. Not all PTO switches function the same, it depends on the manufacturer and how they wire the safety...
Replies: 5
Views: 359
Posted By BFHFixit

Set your gauge wheels to the height you want then...

Set your gauge wheels to the height you want then adjust the deck so the rear is 1/4" higher than the front at the lowest setting.
They set there gauge wheels at the lowest for shipping to gain an...
Replies: 49
Views: 1,704
Posted By BFHFixit

Make sure your choke is operating correctly.

Make sure your choke is operating correctly.
Showing results 1 to 25 of 200
 


 
Forum Jump