Search: Posts Made By: CAMINO KID
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 40
Views: 4,667
Posted By CAMINO KID

There is a product called E-Z-Pour that is...

There is a product called E-Z-Pour that is available in hardware stores and many other outdoor equipment places that comes in two lengths that will replace about 90% of the spouts on most gas cans. ...
Replies: 9
Views: 624
Posted By CAMINO KID

you might try removing the choke blade and...

you might try removing the choke blade and reorienting the shaft and then reinsert the choke blade. I do not see the choke blade area to verify it.
Replies: 3
Views: 2,700
Posted By CAMINO KID

You probably had some gummy residue from the last...

You probably had some gummy residue from the last years fuel somewhere either at the needle valve or the float pivot causing the fuel to leak through the carb. After the present fuel you installed...
Replies: 11
Views: 7,836
Posted By CAMINO KID

no drive

3670georgia - have you taken the gears off the axle shaft? The gears have "L" or "R" stamped on the edge of them. When the gears are installed on the axle shaft the keys should push up out of the...
Replies: 11
Views: 7,836
Posted By CAMINO KID

Bushings

Have you checked the bushings in the height adjuster that your transmission axle shaft goes through. This bushing also acts as a thrust washer and will wear the length down to where the axle gear...
Replies: 8
Views: 3,091
Posted By CAMINO KID

Carb jet

more than likely you engine has a plastic carb that is basically from the discontinued Lawn Boy 2cycyle. On the side of the carb is a tape with writing or numbers on it. Under it is a jet that can...
Replies: 106
Views: 79,410
Posted By CAMINO KID

Thanks for the addition as I could not find the...

Thanks for the addition as I could not find the site when I went to reply. I have been away from the shop for over four years now and still follow the site and help when I can. Thanks again.
Replies: 106
Views: 79,410
Posted By CAMINO KID

When I still had the shop after Troybilt went...

When I still had the shop after Troybilt went under, I used the 5/8 belts in the 29 1/4 length that you can get anywhere fan belts are sold. I used the heavy duty belts from Gates for years with no...
Replies: 73
Views: 74,778
Posted By CAMINO KID

make sure your nut is seated in the recess in the...

make sure your nut is seated in the recess in the height adjuster back side. the spacer has a shoulder that seats into the gear cover. you will have to hold the nut in place as you insert the bolt...
Replies: 15
Views: 16,212
Posted By CAMINO KID

You have to remove the belt pulley on the front...

You have to remove the belt pulley on the front housing and then you have the bearing retainer to take the nuts off and then the sides have some bearing retainers also to take the nuts and bolts off....
Replies: 73
Views: 74,778
Posted By CAMINO KID

The cable is adjustable on the side of the handle...

The cable is adjustable on the side of the handle bar. Loosen the nut on the cable holder and move it toward the deck and tighten. A little movement will do a lot. Make sure your belt is correct...
Replies: 73
Views: 74,778
Posted By CAMINO KID

The gear will have an R on one side of it and an...

The gear will have an R on one side of it and an L on the other side. The gears are the same but directional. If you can only see the R on a gear then put the R side inboard direction.
Replies: 73
Views: 74,778
Posted By CAMINO KID

All I can say is it takes some mussel to slid it...

All I can say is it takes some mussel to slid it off. It sounds as if you are trying to replace the upper plastic slide. Unhook every thing and then work the handle over the upper metal tubing...
Replies: 4
Views: 1,434
Posted By CAMINO KID

Take the gears off the axle shaft and look at the...

Take the gears off the axle shaft and look at the side of the gears. You will see an R or L. Put the gears on the axle shaft with the "R" facing out on the right side and the "L" facing out on the...
Replies: 73
Views: 74,778
Posted By CAMINO KID

Take the gears off the axle shaft and look at the...

Take the gears off the axle shaft and look at the side of the gears. You will see an R or L. Put them on the mower with the "R" facing out on the Right side of the mower and the "L" facing out on...
Replies: 8
Views: 2,815
Posted By CAMINO KID

Try this site. Item I am referring to is number...

Try this site. Item I am referring to is number 10.
...
Replies: 2
Views: 1,802
Posted By CAMINO KID

Check safety switches.

This model has to have the brake on and some have to have the seat switch pressed by being seated. Also if the PTO is not showing that it is off you will not complete the circuit that allows the...
Replies: 8
Views: 2,815
Posted By CAMINO KID

Transmission has lost center

Your transmission should not move left or right which I believe the shaft is also moving. The swivel for the wheel adjuster acts as a locator and if you have worn the end of the bushing part of the...
Replies: 106
Views: 79,410
Posted By CAMINO KID

Some of the earlier machines had centrifugal...

Some of the earlier machines had centrifugal clutches. Mine came with an idler and lever setup to tighten the belt to start the chipper after the engine has warmed up. Having serviced both types of...
Replies: 5
Views: 9,851
Posted By CAMINO KID

If you smell gas then change the oil. Your carb...

If you smell gas then change the oil. Your carb must have flooded over the summer and the gas went into the oil. Fresh oil and with fresh gas run it and see if the smoke quits.
Replies: 5
Views: 9,851
Posted By CAMINO KID

Old gas

If you did not drain the winter fuel from last year, you were lucky you got it to run. If you drain the old fuel and put in fresh, the smoke should cease quickly.
Replies: 7
Views: 27,690
Posted By CAMINO KID

The spring has to apply an upward pressure to...

The spring has to apply an upward pressure to seat the needle valve in the carb. This was basically to smooth the flow of fuel to the carb due to machine vibration. The weight of the float should...
Replies: 2
Views: 900
Posted By CAMINO KID

If memory serves me right, since I nolong have...

If memory serves me right, since I nolong have any of the manuals, it goes towards the exhaust port.
Replies: 73
Views: 74,778
Posted By CAMINO KID

The transmission has a differential setup with...

The transmission has a differential setup with one wheel or the other being able to spin freely. The real way to test this is to lightly lift the mower up as you push on the handle and the wheels in...
Replies: 4
Views: 3,533
Posted By CAMINO KID

Check the tube that goes between the air cleaner...

Check the tube that goes between the air cleaner back plate and the engine (possibly the valve cover on this engine) for possible crimping off. The is the breather tube and is shown in the air...
Showing results 1 to 25 of 200
 


 
Forum Jump