Search: Posts Made By: SameBIG CHIEF
Showing results 1 to 25 of 112
Search took 0.02 seconds.
Replies: 7
Views: 4,287
Posted By SameBIG CHIEF

If you have improper resistance you will get the...

If you have improper resistance you will get the double chime as well as have a fault on the system. Verify you have a 2K ohm resistor, the bands should be red black red gold.
Replies: 11
Views: 7,330
Posted By SameBIG CHIEF

By "anything" you mean what? If you have disabled...

By "anything" you mean what? If you have disabled the remote download option you have nothing to worry about. The majority of us alarm installation companies have way more things to worry about,...
Replies: 3
Views: 5,781
Posted By SameBIG CHIEF

I have had several of the L5000 Lynx Touch bad...

I have had several of the L5000 Lynx Touch bad out of the box. They run through the boot screen and then the white screen of death. I have had no luck other than sending them back to honeywell. The...
Replies: 50
Views: 3,159
Posted By SameBIG CHIEF

I personally would go with a Vista 40 or 50...

I personally would go with a Vista 40 or 50 before a 128. They are still pretty straight forward in programming without a lot of higher level menus. You can have 2 wireless receivers on these...
Replies: 15
Views: 7,830
Posted By SameBIG CHIEF

You do indeed have to send the wifi module...

You do indeed have to send the wifi module traffic through alarmnet. They have different levels of service packages for the 5100wifi.
Replies: 16
Views: 5,228
Posted By SameBIG CHIEF

If I had to guess the relay is acting properly....

If I had to guess the relay is acting properly. Unless you have verified with a meter that it is fact staying closed. It sounds more to me that your programming is the issue. You in essence have only...
Replies: 6
Views: 5,443
Posted By SameBIG CHIEF

You can also look into a company called Ip...

You can also look into a company called Ip Datatel they are fairly new and have some neat means of communication.
Replies: 7
Views: 5,893
Posted By SameBIG CHIEF

I understand that this is the "right" way to do...

I understand that this is the "right" way to do it. However there is an easier way for the end user DIY person. Terminals 8,9 are designed for 2 wire detectors and when the 2 wire detector is tripped...
Replies: 2
Views: 2,094
Posted By SameBIG CHIEF

I have added external chimes from ATW and wired...

I have added external chimes from ATW and wired them to the on board relay to trigger on a zone fault. Is pretty simple and works great.

http://www.atwbrand.com/Piezos/pc300.htm
Replies: 14
Views: 33,396
Posted By SameBIG CHIEF

I believe this is solved via PM, but for those of...

I believe this is solved via PM, but for those of you who still would like to know. The installer code is 4 digits and to change the master code you simply enter the installer code then 802 then the...
Replies: 3
Views: 4,769
Posted By SameBIG CHIEF

A better idea instead of sending stills at set...

A better idea instead of sending stills at set intervals is to make sure the DVR has alarm inputs, then you can set up a motion detector to send you a still or clip with a pre and post alarm time.
Replies: 5
Views: 4,758
Posted By SameBIG CHIEF

Being 12 years old I don't think the touch screen...

Being 12 years old I don't think the touch screen keypads will work. They are for P series panels only and at a certain revision number as well. The 6160's will be a no brainer, they will either be...
Replies: 8
Views: 13,550
Posted By SameBIG CHIEF

Not to get too in depth but you can use Zone 1 as...

Not to get too in depth but you can use Zone 1 as a smoke reset for 4 wire smoke. I have only done this with two smokes at one time. You basically take the power from the smokes and put it under zone...
Replies: 6
Views: 3,882
Posted By SameBIG CHIEF

X10 makes all sorts of Power Line Carrier...

X10 makes all sorts of Power Line Carrier devices. Assuming you power is on a common source between your home and shop they should work. They would basically send a signal to a chime in your house...
Replies: 4
Views: 1,873
Posted By SameBIG CHIEF

Okay here is my take on the matter. The...

Okay here is my take on the matter. The installation company is playing hard ball. I understand that they feel that the new company will take the installer code and run around the neighborhood...
Replies: 4
Views: 2,277
Posted By SameBIG CHIEF

Set all switches to off except number 5 it should...

Set all switches to off except number 5 it should be on.
Replies: 8
Views: 4,407
Posted By SameBIG CHIEF

Look on the eeprom chip on the board it will tell...

Look on the eeprom chip on the board it will tell you the revision number. The 4285 were for all panels prior to the new P series. Yes you can program from any keypad as long as it is addressed and...
Replies: 8
Views: 4,407
Posted By SameBIG CHIEF

You need a 4286, the 4285 are for older firmware...

You need a 4286, the 4285 are for older firmware panels. They upgraded probably 3 years ago.
Replies: 16
Views: 1,987
Posted By SameBIG CHIEF

Sounds like you have a termination problem. Just...

Sounds like you have a termination problem. Just about every CCTV system I have seen needs a 75 ohm termination. Most CCTV cable has this resistance in the cable. I know when using old Pelco...
Replies: 14
Views: 2,277
Posted By SameBIG CHIEF

Look in the panel door and tell us what model you...

Look in the panel door and tell us what model you have. It should be in bold print at the bottom of the schematic, or on the outside of the panel box on the door. We can get a little more in depth...
Replies: 9
Views: 41,390
Posted By SameBIG CHIEF

http://www.toshibasecurity.com/pdf/_manuals/IK-WB1...

http://www.toshibasecurity.com/pdf/_manuals/IK-WB15A_user_guide.pdf

You could probably get good use out of one of these. It is one of Toshiba's network cameras. You can set it to e-mail you when...
Replies: 12
Views: 1,487
Posted By SameBIG CHIEF

It isn't that hard, I hate to ask but anyway you...

It isn't that hard, I hate to ask but anyway you could PM your phone number and I can walk you through it by asking you what you see. I am in the EST so take that in mind. If you want let me know a...
09-09-07, 05:35 PM
Replies: 1
Views: 792
Posted By SameBIG CHIEF

Help with ceramic tile installation

I have read books and looked at several DIY sites, but I am still unclear of how to lay-out the chalk lines. Some state to measure the center point both ways and snap lines, while others say to lay...
Replies: 3
Views: 8,101
Posted By SameBIG CHIEF

The 1 and 2 you speak of is partion numbers not...

The 1 and 2 you speak of is partion numbers not actual program data. Anywhere you see this you need to enter the information for both patition sections. For example *21 is Exit Warning, you would...
Replies: 12
Views: 1,487
Posted By SameBIG CHIEF

I was afraid it would be on an expander. What...

I was afraid it would be on an expander. What type of keypad do you have? Does it say Disarmed Ready to Arm on the screen or just Ready or Not Ready?
You really need an Alpha keypad to do this since...
Showing results 1 to 25 of 112
 


 
Forum Jump