Search: Posts Made By: lightspeed
Showing results 1 to 25 of 200
Search took 0.03 seconds.
08-20-19, 09:09 AM
Replies: 5
Views: 279
Posted By lightspeed

As far as I know, it is a solid wood door, when...

As far as I know, it is a solid wood door, when it was installed seem to weigh a ton.

I want to thank U'all for the prompt response!!
Replies: 11
Views: 462
Posted By lightspeed

Seem to recall with some 'yard tools' the...

Seem to recall with some 'yard tools' the replacement components are non-adjustable?

If after attempting to start the engine with no success, and find the plug wet, I would suggest let the tool...
08-20-19, 08:13 AM
Replies: 5
Views: 279
Posted By lightspeed

Trim interior door to fit

Interior door is dragging on the carpet so I want to trim approx. 3/4" off the bottom. I currently have a standard saw blade on my skill saw, would this be suitable for making the cut; if not, any...
Replies: 4
Views: 369
Posted By lightspeed

I appreciate U'r comments and suggestions. After...

I appreciate U'r comments and suggestions. After reviewing the comments I left messages with a couple foam insulation business in my area, depending upon the cost and estimated time to complete the...
Replies: 4
Views: 369
Posted By lightspeed

Insulating a Corrugated Metal Building

I have a 16' x20' corrugated building that I am using as a garage/workshop and I would like to insulate the structure so I use it during the winter months. I have come across a couple insulation...
Replies: 4
Views: 396
Posted By lightspeed

I will clean the existing slab, frame for the new...

I will clean the existing slab, frame for the new then use the groove tool goove tool.

U's input has been very helpful, I thank Y'all I now feel confident I can proceed with my project.
...
Replies: 4
Views: 407
Posted By lightspeed

Sounds a lot less labor-intensive than scrubbing,...

Sounds a lot less labor-intensive than scrubbing, there are another 30 feet of retainer wall on the other side of the entrance, my pressure washer should have it prepped in proby less than a...
Replies: 4
Views: 396
Posted By lightspeed

There is sand between the joints.

There is sand between the joints.
Replies: 4
Views: 407
Posted By lightspeed

I thank you, considering using a very mild,...

I thank you, considering using a very mild, perhaps 5% solution of muriatic acid, or TSP?
Replies: 4
Views: 396
Posted By lightspeed

extending cement slab

There used to be a drain running beneath the brick just prior to the entrance. Thought I would remove approx. 2' to 3' of bricks then use 2"x6" to frame for a slab and marry it to the existing slap...
Replies: 4
Views: 407
Posted By lightspeed

Cleaning surface of retaining wall

I poured the retaining wall a few years ago but before installing the new screen door I want to set bricks along the top of the wall, should I clean the surface with a mild cleaning solution that...
Replies: 3
Views: 1,086
Posted By lightspeed

Certain I overcompensated for the slope due to...

Certain I overcompensated for the slope due to the amount of annual rainfall in my area and set the gutter below the flashing towards the drain pipe. I intend swapping to different type of hanger. I...
Replies: 3
Views: 1,086
Posted By lightspeed

Gutter-Fascia-Splash Guard

In the process of replacing gutters and in doing so I want to prep the fascia for the gutter reinstall. Not an authority, it does not appear the fascia needs to be replaced, I am sanding and...
Replies: 5
Views: 858
Posted By lightspeed

If unsuccessful may consider purchasing a...

If unsuccessful may consider purchasing a replacement kit, there are a number of sources for the repair kit, purchased mine thru Amazon. The kit I purchased included the carburetor, fuel lines,...
Replies: 5
Views: 357
Posted By lightspeed

Great suggestion, I thank you!!. I will contact...

Great suggestion, I thank you!!. I will contact local building supply outlets Tuesday to inquire if they offer the mortar mix in various color, or an additive to obtain same effect. I think 2 or 3...
Replies: 5
Views: 357
Posted By lightspeed

Thank you for the suggestion, giving the pattern...

Thank you for the suggestion, giving the pattern some thought and starting from the center and working out seems the better option.

By framing meant I have cut the 12 pieces of 4"x 6" and set...
Replies: 5
Views: 357
Posted By lightspeed

Standard Brick pattern for Hexagon Patio

I cut the framing for 12' dia. hexagon patio and curious if member's have suggestion on the type of pattern that works best with minimal amount of cutting. I will be using standard red clay type...
Replies: 15
Views: 928
Posted By lightspeed

'Chime-in' is good food for thought!! Thank U

'Chime-in' is good food for thought!! Thank U
Replies: 15
Views: 928
Posted By lightspeed

We used the VCR last night and satisfied with the...

We used the VCR last night and satisfied with the quality of the picture, as noted in previous thread, our VHS selection is quite limited, I can count the number of times the VCR is used in a month...
Replies: 15
Views: 928
Posted By lightspeed

Life is Good!!! Using the existing Component...

Life is Good!!! Using the existing Component cables as instructed, took a matter of 30 seconds, it works!!!

I can not thank U's all enough! 72110
Replies: 15
Views: 928
Posted By lightspeed

I agree, if using the existing component cables...

I agree, if using the existing component cables work it's 'plug and go' that is about as much labor I intend putting into it.

Thank you for the input!
Replies: 15
Views: 928
Posted By lightspeed

The TV and A/V receiver are approx. 1 yr. old and...

The TV and A/V receiver are approx. 1 yr. old and appears there are few input jacks that are not begin used. Currently all components are running thru the A/V using HDMI, except for this 1 Component...
Replies: 15
Views: 928
Posted By lightspeed

Greatly appreciated every one's input!! ...

Greatly appreciated every one's input!!

Correct, that is what I hope to do, use the existing component cables to operate the VHS; was not clear which color pins to plug into what color jacks?...
Replies: 15
Views: 928
Posted By lightspeed

I greatly appreciate U all's responding!! ...

I greatly appreciate U all's responding!!

The VHS is a Sanyo, 'ugg', there are a set of component outlets on the back of the unit indicating DVD, and another set of composite outlets for both...
Replies: 15
Views: 928
Posted By lightspeed

Composite vs Component

It is possible to use Component cables in lieu of Composite?

Entertainment center where cables are routed thru the walls. I ran Component cables to connect DVD player to TV. Recently replaced DVD...
Showing results 1 to 25 of 200
 


 
Forum Jump