Search: Posts Made By: crom60
Showing results 1 to 25 of 47
Search took 0.02 seconds.
Replies: 2
Views: 1,523
Posted By crom60

lawntractor snowblower attachment

I have a old agway ( mtd 800 ) tractor woth a snowblower attachment. I keep throwing the belt that runs the auger ( belt # 754 0295) after hours of searching I found a ipl for the blower unit. now my...
Replies: 3
Views: 14,474
Posted By crom60

Did you hit anything before it died ? first I...

Did you hit anything before it died ? first I would check the spark could be a number of things if you get no spark but I would look at the coil first.



...
Replies: 8
Views: 1,742
Posted By crom60

Don't most riders have 2 drive belts ?

Don't most riders have 2 drive belts ?
Replies: 83
Views: 28,343
Posted By crom60

The problem is that there is no longer an...

The problem is that there is no longer an ignition switch, just wires not connected to anything. Well I would look into a switch first of all. Did he hook the jumper cables to the battery and put the...
Replies: 16
Views: 6,765
Posted By crom60

clean and rebuild the carb

clean and rebuild the carb
Replies: 4
Views: 1,063
Posted By crom60

Is there a nut on the other end of the shaft my...

Is there a nut on the other end of the shaft my 46 inch murray has does.
Replies: 5
Views: 1,600
Posted By crom60

Well I can tell you that a slow cranking starter...

Well I can tell you that a slow cranking starter can be a sign the starter is on the way out the door, For a week or more I was haveing the same problem then today I went to start the mower and...
Replies: 1
Views: 1,055
Posted By crom60

402700 carb rebuild

Hello I have a B&S 402700 18.5 hp engine. Last year I bought the rebuild kit for the carb, I was hopeing to find some sory of manule to help me preform the carb rebuild.

...
Replies: 10
Views: 1,288
Posted By crom60

I love my old mtd with a twin cyl 18 bs, I once...

I love my old mtd with a twin cyl 18 bs, I once towed a small RV with it ! I use it now mostly for snowblowing real hard to bog down the engine. Yes they are harder to work on but preformance is well...
Replies: 8
Views: 5,378
Posted By crom60

Auger free wheels ? with the engine off try...

Auger free wheels ? with the engine off try turning the auger by hand if it moves more than just a bit its prob a shear pin. Most blowers I know have 2 shear pins 1 on each auger blade.


...
Replies: 3
Views: 725
Posted By crom60

Yes it does mount with 4 bolts but the started...

Yes it does mount with 4 bolts but the started doesn't engage the flywhel if this or the other bottem bolt is of for some reason. I was thinking of filling it in and retaping it with some sort of...
Replies: 3
Views: 725
Posted By crom60

Starter Mount

Hello I have a Teu 8hp side shaft Hsmk80 or something like that. My problem is the bottem right bolt hole on the engine block that the starter mounts on has broke and now I am stuck pull starting...
Replies: 11
Views: 6,173
Posted By crom60

Also check to make sure the mounting bracket has...

Also check to make sure the mounting bracket has not broke, I just had the same problem on mine the bracket had broke free a bit. So the flywheel and the starter did not mesh up.

...
Replies: 5
Views: 1,069
Posted By crom60

I did that over the summer didn't lap the valves...

I did that over the summer didn't lap the valves I have tried to adjust the carb and its of no big help. Winters here and was just wondering if I could use the flames as a hard warmer or worry if it...
Replies: 5
Views: 1,069
Posted By crom60

flames

I have a old Noma snowblower with a 8 hp motor on it. It runs great but what concerns me is after replaceing the stock muffler with a screw in BS round screw in muffler when I see flames shooting out...
Replies: 9
Views: 1,854
Posted By crom60

Puey61 is right if you buy a good machine and...

Puey61 is right if you buy a good machine and take care of it should last you forever. Case in point my gilson 8 hp dual stage is well over 10 years old and I live in a place that gets 160 inchs of...
Replies: 3
Views: 786
Posted By crom60

yup the good old b&s 3/4 pipe muffler fits just...

yup the good old b&s 3/4 pipe muffler fits just fine seems to run good after some tweeking of the carb only worry I have is the paint burnt right off the new muffler. When I got the muffler the...
Replies: 3
Views: 786
Posted By crom60

muffler

I have a 8hp h shaft Tecumseh I think its a hmsk something. Anyway while pulling the muffler off I broke the bolts holing it on. I have tried everything short of tapping them then I noticed the...
Replies: 5
Views: 1,069
Posted By crom60

Well I waited 2 days to run it again but you do...

Well I waited 2 days to run it again but you do think its still the carb I know I had to rebuild that anyway.


Crom
Replies: 5
Views: 1,069
Posted By crom60

Briggs 16 2 cyl problems

Last week while messing around with this engine ( Birggs & Stratton 16 hp 2 clylinder 402707 model #) It would not start and I noticed the carb was filled with gas. I thought to myself lucky boy you...
Replies: 7
Views: 9,075
Posted By crom60

Deck adjustment, tires under inflated and belive...

Deck adjustment, tires under inflated and belive it or not on my mower I had the same problem and the blade adaptor had rounded out.

Crom
Replies: 3
Views: 1,160
Posted By crom60

Depends on how good it is, Kinda like playing...

Depends on how good it is, Kinda like playing russion roulet hard to tell when its going to start breaking down. How often was it use how big was his yard and remmeber its 8 years old.


...
Replies: 2
Views: 859
Posted By crom60

deck woes

hello I have a old murray 46 inch deck 3 blades I went to sharpen the blade yesterday and when I put them back on I heard a clicking sound when I engaged the blades, A little look see and I saw the...
Replies: 14
Views: 85,181
Posted By crom60

I am just glad no one suggested to tap on the...

I am just glad no one suggested to tap on the carb to free the float :-)

Crom
Replies: 3
Views: 1,100
Posted By crom60

First thing to do is check the auger and make...

First thing to do is check the auger and make sure its not blocked next I would check the auger belt. I can see no reason why changeing the chute pos would hurt the snowblower. Check those 2 things...
Showing results 1 to 25 of 47
 


 
Forum Jump