Search: Posts Made By: banjoman
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Replies: 12
Views: 1,011
Posted By banjoman

This deck was built about 17 years ago when we...

This deck was built about 17 years ago when we had an addition put on to our house. I've added joist hangers and had to raise up a few joists to even them up but I've got it all ready for the boards...
Replies: 12
Views: 1,011
Posted By banjoman

Here is another pic close up of the corner. I use...

Here is another pic close up of the corner. I use structural screws to pull that board that is on the front of the deck Flatt cuz it was cupped pretty bad now if I can just get the lag bolts taken...
Replies: 12
Views: 1,011
Posted By banjoman

Here is a pic of the deck and the lag bolts, I...

Here is a pic of the deck and the lag bolts, I took this picture was before I had all the decking ripped off, I've got it all off and just laid composite boards on top now.
Replies: 12
Views: 1,011
Posted By banjoman

Sorry, the bolts on the outside of the deck that...

Sorry, the bolts on the outside of the deck that are holding the deck up. Im putting composite on and need to put fascia over the old treated 2x10 frame, rim joist or whatever you call it? of the...
Replies: 12
Views: 1,011
Posted By banjoman

Lag bolts and fascia

I want to pull the lag bolts so I can install fascia on my deck, is there a bracket or hanger or something that can be used to accomplish this?
Replies: 2
Views: 908
Posted By banjoman

Deck fascia help

I'm getting ready to install new decking on my old deck I ripped off old 2 by 6 treated boards and I'm putting down composite grooved boards. the problem I'm having is figuring out what to do at the...
04-14-19, 12:08 PM
Replies: 1
Views: 282
Posted By banjoman

ceiling repair help

repairing a ceiling from hurricane Florence . Should I square up the opening? I cut out where it was wet and on the one end you can see I went past the rafter by about 4 inches, should I just cut to...
11-09-15, 02:51 PM
Replies: 3
Views: 591
Posted By banjoman

Thanks guys, I'll call and let you know what they...

Thanks guys, I'll call and let you know what they find.
11-09-15, 07:50 AM
Replies: 3
Views: 591
Posted By banjoman

Random lights and power outages

For a while our addition on our house, the lights would go dim and bright often and now they don't work along with a few recepticals. I was checking the breakers and my non touch tester shows some of...
07-22-13, 04:06 AM
Replies: 3
Views: 4,484
Posted By banjoman

The motor has a plate and under that are wires, I...

The motor has a plate and under that are wires, I connected all 5 wires according to the manufacturer diagram and had a couple others verify is correct. The switch changes around the hot and neutral...
07-21-13, 06:32 AM
Replies: 3
Views: 4,484
Posted By banjoman

problems with boat lift reversing motor and switch help

I have had this lift running for 10 years and then it started tripping the gfci circuit. I had an electrician run new wiring to that circuit and install new gfci outlets. Still having a problem with...
02-20-11, 03:02 PM
Replies: 1
Views: 1,012
Posted By banjoman

Amana heat pump question

Had 2 new digital thermostats installed 2 days ago, this morning one thermostat is dead, no power between the C connection wich is the blue wire and the red wire. I have an upstairs unit same exact...
Showing results 1 to 12 of 12


 
Forum Jump