Search: Posts Made By: dave237
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 4
Views: 721
Posted By dave237

Thanks

Cheese,

I will do so. It will be a while before I'll be able to work on these. I'll reply back as soon as I can. Thanks again for all you guys help.

Dave237
Replies: 4
Views: 721
Posted By dave237

Thanks!

Thanks much. I'm believeing the same thing. The only thing both engines had in commen with each other is the same gas and their being under the same tarp together. Ethel will $uck up some gaskets I'm...
Replies: 4
Views: 721
Posted By dave237

Carb/intake Problem

Hey all. It's been a while since I've been around. I've got a funny problem and thought you guys might offer some insight, I hope you hear me cheese.

I've got a pair of mowers one is a 11.5 horse...
Replies: 20
Views: 3,062
Posted By dave237

NAVYDAD, Check your gas cap vent. It may be...

NAVYDAD,

Check your gas cap vent. It may be clogged.

Dave237
Replies: 6
Views: 7,091
Posted By dave237

Jack B., Agreed! Either 1/4 turn out or 1/4...

Jack B.,

Agreed! Either 1/4 turn out or 1/4 turn in; it all boils down to the same thing. Cloged jet or vacume leak..... I guess it's up to you to decide?

Dave237
Replies: 4
Views: 1,828
Posted By dave237

VeggieMan, Nope, it will not hurt the...

VeggieMan,

Nope, it will not hurt the ignition coil to run however, I must say that you need a new key switch. Replace it.

Dave237
Replies: 3
Views: 1,890
Posted By dave237

woodguy, Remove the kill wire from the coil...

woodguy,

Remove the kill wire from the coil and switch. Now, give it a try. Sometimes the wire can have nick that arks.....!

Dave237
Replies: 6
Views: 7,091
Posted By dave237

Jack, At idle; set the idle jet screw in...

Jack,

At idle; set the idle jet screw in until seated. I'm sure you will get a response. If not, you have a vacume leak.

Dave237
Replies: 16
Views: 2,091
Posted By dave237

cmw0021, You still have a problem with the...

cmw0021,

You still have a problem with the carb. Make sure your choke choke flap is closing on start up and opening once warm. Also, did you adjust the idle jet when you put the carb back. 1 1/2...
Replies: 16
Views: 2,091
Posted By dave237

cmw0021, The old O-ring...... and not seal;...

cmw0021,

The old O-ring...... and not seal; under the screw, can get you sometimes. I'm glad it's vrooming.... You deserve the pat on the back. You solved the problem yourself. Congrats....!
...
Replies: 2
Views: 2,363
Posted By dave237

74roostu, Sounds like the fly weights on the...

74roostu,

Sounds like the fly weights on the govenor shaft have broken. You'll need to open up the engine to repair this however, some others here may know something specific pertaining to the...
Replies: 7
Views: 20,931
Posted By dave237

Gravely, Your breater or (PCV) valve is...

Gravely,

Your breater or (PCV) valve is gone. Follow the hose from the carb breather to the crank case breather. There are two screws that holds it into the valve case. Remove and replace it along...
Replies: 16
Views: 2,091
Posted By dave237

cmw0021, The needle is held very losely...

cmw0021,

The needle is held very losely indeed but on purpose. This keeps it from hanging in the seat which just very well may be your problem.

Cheese is correct in this being a very cheap...
Replies: 16
Views: 2,091
Posted By dave237

cmw0021, In your picture, (nice job), the...

cmw0021,

In your picture, (nice job), the part you referred to as a seal seems to be an O-ring and if indeed this part is the problem replace it. You should also look at the the float inlet...
Replies: 13
Views: 1,560
Posted By dave237

SIDVICIOUS, Great!! That's what we like to...

SIDVICIOUS,

Great!! That's what we like to hear. I'm glad we could be of help!

God Bless,
Dave237
Replies: 23
Views: 1,410
Posted By dave237

Lex, The very small 300ma/Hour or .3...

Lex,

The very small 300ma/Hour or .3 Amp/Hour rating difference will not cause a problem.

Dave237,
God Bless
Replies: 23
Views: 1,410
Posted By dave237

Lex, If the batt numbers match and ampere...

Lex,

If the batt numbers match and ampere hour rating is the same or greater, (at your web address 2.2A/H), is the same as the old batt; then yes!

Dave237,
God Bless
Replies: 23
Views: 1,410
Posted By dave237

Lex, It's had it..... No more charging . If...

Lex,

It's had it..... No more charging . If after 9 hours charging it's not holding the reverse chemical charge; you're wasting electrons. You can charge it till domes day....It's done.

You...
Replies: 8
Views: 9,317
Posted By dave237

cactusman, nascar 20 fan, is correct! This...

cactusman,

nascar 20 fan, is correct! This is a Tecumseh engine and the numbers you supplied is for this engine and not for the mower itself.

The CPD internet address he supplied will give you...
Replies: 15
Views: 1,523
Posted By dave237

pearex, Cheese, can help you out here. ...

pearex,

Cheese, can help you out here.

He is very very good with self propelled mowers, even electric ones that discharge from the side. These also, qualify as outdoor power equipment and he...
Replies: 4
Views: 1,194
Posted By dave237

catpuff, Engines + Mower's, "now day's"; are...

catpuff,

Engines + Mower's, "now day's"; are like comparing Apple's to PC's. One may have this but the other may not have that for this $$$$.

Either way, you'll turn a wrench at one point or...
Replies: 2
Views: 2,818
Posted By dave237

hopkinsr2, Thank you much. Sounds like you...

hopkinsr2,

Thank you much. Sounds like you are in the know.....! You have gave the answer I was looking for. Thank you for your reply! It does have a shielded plug wire, indeed!!! However, this...
Replies: 14
Views: 10,216
Posted By dave237

Polydorus, It maybe too late but check the...

Polydorus,

It maybe too late but check the gas tank flatness with a straight edge and feeler gauge. If you can insert a .002 feeler between the tank and straight edge then it's questionable..????...
Replies: 7
Views: 1,678
Posted By dave237

toni1595, Believe me, it's wonderful stuff...

toni1595,

Believe me, it's wonderful stuff in a dire emergency and will get you going however, if you are going to be the one whom 3 years later has to pull, bang, beat, treat, sweat, curse and...
Replies: 2
Views: 2,818
Posted By dave237

Duro Power

Anybody know about Duro Power generator engines? It's an odd one..... 8 hp OHV, slant horizontal design.... I've never seen one until now.

Thanks in advance for any input!

Dave237,
God Bless
Showing results 1 to 25 of 200
 


 
Forum Jump