Search: Posts Made By: jl66redcpe
Showing results 1 to 25 of 200
Search took 0.03 seconds.
Replies: 7
Views: 1,042
Posted By jl66redcpe

I purchased off ebay a spark plug wire connector...

I purchased off ebay a spark plug wire connector a while back. I was just for this purpose.
Replies: 3
Views: 249
Posted By jl66redcpe

JD 105 with Briggs 17.5 HP Broken Rocker Arm

A customer stopped by today and said he had a John Deere 105 with a Briggs 17.5 HP engine and the rocker arm broke in half and the push rod was bent. Now, I can certainly fix it however, i would...
Replies: 16
Views: 472
Posted By jl66redcpe

You need to remove the key from the flywheel to...

You need to remove the key from the flywheel to really check it. If you have not done this, you have not checked it. Even a partially sheared key will cause what you are experiencing.
Replies: 6
Views: 282
Posted By jl66redcpe

I owned a Troy Bilt Horse tiller from the 70's. ...

I owned a Troy Bilt Horse tiller from the 70's. I was a very well built machine and very powerful. It has the standard 6hp tecumseh engine on it. i kept sea foam in the gas and maintained the...
Replies: 4
Views: 308
Posted By jl66redcpe

Job is all finished. Tractor moves fine. The...

Job is all finished. Tractor moves fine. The instructions in the sears manual are worthless. It leaves out many steps. Nest one could be much easier. I documented my steps.
Replies: 4
Views: 308
Posted By jl66redcpe

I ended up dropping the electric clutch and the...

I ended up dropping the electric clutch and the belt went on the engine pulley pretty easy. Now I am trying to get the belt around the transaxle pulley and that is a real problem. I see the hole in...
Replies: 4
Views: 308
Posted By jl66redcpe

thank you -- the mech stop is there. I wasnt...

thank you -- the mech stop is there. I wasnt sure if I could easily remove it. It looks like it has a square head.
Replies: 4
Views: 308
Posted By jl66redcpe

Craftsman Rider 917-258910 Motion Drive Belt

I need to change out the motion drive belt on this craftsman rider. Do I have to remove the electric clutch to change this belt ?? The owners manual does not mention it either way. This...
Replies: 1
Views: 373
Posted By jl66redcpe

Kohler cv22-67515 with smart spark - coils

I have a kohler cv22-67515 with smart spark in the shop only running on one cylinder. Supposedly the correct coil was a 24-584-36-s. However that is wrong as it is too big. The correct coil...
Replies: 1
Views: 355
Posted By jl66redcpe

Nevermind - I just found a youtube video. Sorry

Nevermind - I just found a youtube video. Sorry
Replies: 1
Views: 355
Posted By jl66redcpe

Jonesreed AWD mower replace belt

I have a Jonesred model 96142012300 AWD mower in the shop. The drive belt jumped off. I have the operators manual which tells you how to replace the belt. I cannot get the debris shield off. It...
Replies: 3
Views: 379
Posted By jl66redcpe

I use a vacuum pump and then check it with a coat...

I use a vacuum pump and then check it with a coat hangar to make sure it is empty. The dipstick shows perfectly clean new oil. I am concerned that the oil is not making it into the oil filter.
Replies: 3
Views: 379
Posted By jl66redcpe

Oil Filter Dilema on Kohler Command Engines

This is an email I just sent to an ebay seller regarding a pack of 12 oil filters for Briggs, Kohler, Kawasaki etc. Any comments from you folks.

Hi -- I repair power equipment. I have used one...
Replies: 6
Views: 390
Posted By jl66redcpe

My shop is currently filled with MTD products. ...

My shop is currently filled with MTD products. One TroyBilt rider in for service and with the broken spring. Two Cub Cadets both have decks that have just dropped down. Huskee push mower that...
Replies: 6
Views: 390
Posted By jl66redcpe

thanks Cheese -- I am familiar with the spring...

thanks Cheese -- I am familiar with the spring you reference. it is not that one. I have removed the spring you reference many times when changing belts and pulleys on these mtd/troybilt models. I...
Replies: 6
Views: 390
Posted By jl66redcpe

wire puller thank you very much - the spring is...

wire puller thank you very much - the spring is part of the transmission drive assy and not the deck.
Replies: 6
Views: 390
Posted By jl66redcpe

Help - Where does this spring go

Have a Troy Bilt Bronco riding mower 13YX78KS011 DOM 2013 in the shop for service. While checking it out I noticed that the mower would keep going after you let off the drive pedal. I called the...
Replies: 6
Views: 340
Posted By jl66redcpe

Cheese - thanks -- removed all the check valves...

Cheese - thanks -- removed all the check valves -- they looked ok. Tried your suggestion and could not get any pressure out of it. Looks like I will get a new pump.
Replies: 6
Views: 340
Posted By jl66redcpe

It has a horizontal briggs motor on it.

It has a horizontal briggs motor on it.
Replies: 6
Views: 340
Posted By jl66redcpe

Pressure Washer no pressure

I have a Model CH2403 S/N 227629 Chore Master pressure washer. It is made by Mite T M. I went to use it and it has no pressure. When I put it away for the winter I did my usual maintenance of...
Replies: 13
Views: 2,482
Posted By jl66redcpe

Checked the bolts. They were all right. Just a...

Checked the bolts. They were all right. Just a really crummy engine.
Replies: 13
Views: 2,482
Posted By jl66redcpe

thank you -- will do hopefully today

thank you -- will do hopefully today
Replies: 13
Views: 2,482
Posted By jl66redcpe

OK I replaced the carb with a chinese carb from...

OK I replaced the carb with a chinese carb from ebay. Engine starts fine and does not backfire. It does not surge under load however at no load it does. Also as it is surging from low speed to...
Showing results 1 to 25 of 200
 


 
Forum Jump