Search: Posts Made By: bobcanuck
Showing results 1 to 25 of 33
Search took 0.02 seconds.
Replies: 3
Views: 588
Posted By bobcanuck

update ... able to unfasten (from hinges) the...

update ... able to unfasten (from hinges) the door from the unit (as well as the "choke" etc) but unable to locate electrical plug that must be disconnected to allow me to fully remove the door. ...
Replies: 3
Views: 588
Posted By bobcanuck

Thank you ... I appreciate the hint.

Thank you ... I appreciate the hint.
Replies: 3
Views: 588
Posted By bobcanuck

KitchenAid khms2050 repair instructions ...

I need to replace the control panel circuit board which is in the microwave door ... board prt no WP8206635. Nowhere can I find step by step instructions on how to safely (ie not damage)...
Replies: 12
Views: 859
Posted By bobcanuck

Thanks for the information and the offer ... much...

Thanks for the information and the offer ... much appreciated ...
Replies: 12
Views: 859
Posted By bobcanuck

Thank you sincerely ... I will keep your offer...

Thank you sincerely ... I will keep your offer in mind ...
Replies: 3
Views: 461
Posted By bobcanuck

Thank you Mark ... once I remove as much of the...

Thank you Mark ... once I remove as much of the old caulk as I can, I will wash with Javex/Javel (chlorine) allow to dry, rewash with alcohol and then apply fresh caulk. Once again, thnx
...
Replies: 3
Views: 461
Posted By bobcanuck

recaulking shower base ...

The caulk between the shower base and tile wall is showing it's age. Can I just scrape/cut off the old and redo or is there more to the process than I imagine? If traces of the old silicone remain,...
Replies: 12
Views: 859
Posted By bobcanuck

Hard drive backup/copying ...?

My hard drive makes strange noises at times - I suspect it is dying !
Before it does, can I copy it's contents to a CD or memory stick or ... so that when I do replace it (I believe the new hard...
Replies: 2
Views: 553
Posted By bobcanuck

Replacement ceramic cartridge ...

background ... I have a tub which fills via the "overflow" and has a hand-held sprayer as well. The water temp, volume and direction (ie fill or spray) is controlled via a stand alone...
11-23-14, 08:37 AM
Replies: 2
Views: 704
Posted By bobcanuck

Thank you Tom, for your suggestion. I agree ......

Thank you Tom, for your suggestion. I agree ... the unit is a "bottom of the line" Lennox and has not been serviced since install (5 yrs). Perhaps I should have the "fins" cleaned out (from the...
11-21-14, 08:47 AM
Replies: 2
Views: 704
Posted By bobcanuck

Lennox heat pump running & running & running ...

The outside temp here is approx. 20 F ... I am in a relatively "tight" condo.
The HP seems to run forever to increase the inside temp 1 deg F ... no frosting on the coil that I can see.
Is this a...
Replies: 2
Views: 560
Posted By bobcanuck

No, no instructions. Thank you - your suggestion...

No, no instructions. Thank you - your suggestion makes sense.

Bob
Replies: 2
Views: 560
Posted By bobcanuck

Sedal cartridge installation .... how tight?

I've finally found the correct replacement cartridge (thanks to an exceptional guy at the local Home Depot). The cartridge sits in a "barrel" and is held in place by a threaded cap (on top). My...
07-26-13, 10:47 AM
Replies: 1
Views: 754
Posted By bobcanuck

VisionPro IAQ programming ...

Thanks to significant help from this forum, my system is generally working well !!! My question - to me, it appears that the "system" is a little too sensitive. Is there a "setup function" where...
02-15-13, 08:53 AM
Replies: 3
Views: 856
Posted By bobcanuck

Greetings Jay. I went through the complete...

Greetings Jay. I went through the complete set-up sequence again this morning, using your previously advised settings - guess what? Seems to be functionning properly once again !!!
I sincerely...
02-14-13, 01:55 PM
Replies: 3
Views: 856
Posted By bobcanuck

Jay - God of Honeywell thermostats ... I need help again (progamming)

You helped me install a VisionPro with Truesteam successfully - thank you !!!
At the moment, however, the fan does not respond to "on" or "circ" from the panel. The humidifier works fine, heat/fan...
04-08-11, 07:22 AM
Replies: 2
Views: 1,419
Posted By bobcanuck

Thank you - the diagram is especially helpful !!!

Thank you - the diagram is especially helpful !!!
04-07-11, 02:26 PM
Replies: 2
Views: 1,419
Posted By bobcanuck

Vision Pro 9000 & outdoor temp sensor ...

I have a TH9421C 1004 thermostat with EMI and Tru Steam humidifier. I want to install an outdoor temp sensor - C7089U 1006 You opined that it would probably work if I ran the sensor wires within...
04-02-11, 11:34 AM
Replies: 3
Views: 1,344
Posted By bobcanuck

Thank you for your opinions ... Bob

Thank you for your opinions ...
Bob
04-01-11, 10:53 AM
Replies: 3
Views: 1,344
Posted By bobcanuck

Honeywell outdoor temp sensor ...

I use a Honeywell IAQ 9000 thermostat; I want to instal the compatible outdoor temp sensor (already have it). My only route from the outside to the thermostat is via the multi wire cable from the...
10-01-10, 10:09 AM
Replies: 2
Views: 1,454
Posted By bobcanuck

Thanks for the info ... yes, I did screw up !!!

Thanks for the info ... yes, I did screw up !!!
09-30-10, 09:49 AM
Replies: 2
Views: 1,454
Posted By bobcanuck

grout waterproofing ...

I've laid porcelain tiles on the balcony (KeraBond, KeraLastic and UltraColor grout). I am concerned with water pooling in several areas as I live in a freeze/thaw climate. Can I (shoud I) use a...
09-03-10, 11:06 AM
Replies: 4
Views: 1,436
Posted By bobcanuck

thanks for the feedback ...

thanks for the feedback ...
09-01-10, 09:53 AM
Replies: 4
Views: 1,436
Posted By bobcanuck

how to disguise granite joints ...

I've had 5 pieces of absolute black granite installed as a fireplace surround. The workmanship is pretty good yet I would like to further disguise the joints, if possible. I've thought of black shoe...
08-22-10, 12:54 PM
Replies: 14
Views: 2,846
Posted By bobcanuck

I would like to thank everyone who took the time...

I would like to thank everyone who took the time to comment/advise ... I'll "go at it" again tomorrow, taking into consideration your thoughts.
Once again, thanks

Bob
Showing results 1 to 25 of 33
 


 
Forum Jump