Search: Posts Made By: kem1966
Showing results 1 to 18 of 18
Search took 0.02 seconds.
Replies: 8
Views: 2,286
Posted By kem1966

If your framing with 2x10's, 16 on center, the...

If your framing with 2x10's, 16 on center, the longest span you should use is 13 feet. And depending on the decking material, it may call for 12" on center. You would have been better off framing...
Replies: 3
Views: 953
Posted By kem1966

Hi, the model # is WFXD 5200 UC/01. The type...

Hi,

the model # is WFXD 5200 UC/01. The type is WAM1.

This washer has the touch screen. And your right about the water saver model. This is the first problem I have had since I owned it, about...
Replies: 3
Views: 953
Posted By kem1966

Siemens washer jumps through cycles

I have a Siemens washer that after loaded and the wash cycle is set, the door will lock, it will fill with water, then drain right out and that ends the washers job.
Any idea what would cause this?
Replies: 25
Views: 9,166
Posted By kem1966

If you ever make it to the Boston area, let me...

If you ever make it to the Boston area, let me know and I'll take you out for one.....or two. I'll even throw in a steak
Replies: 25
Views: 9,166
Posted By kem1966

Thumbs up Hi, I decided to get a new aquastat to...

Hi,

I decided to get a new aquastat to repair the problem. I found out the boiler was installed in 1974, so the odds where better if I replaced it. I was kind of nervous too if I had it all apart...
Replies: 25
Views: 9,166
Posted By kem1966

One more pic. It may give a better view

One more pic. It may give a better view
Replies: 25
Views: 9,166
Posted By kem1966

Hi again, I'm not sure if this would mean...

Hi again,

I'm not sure if this would mean anything, but while looking at the aquastat, there looks to be some dried out material behind the relay. Do you think that would have anything to do with...
Replies: 25
Views: 9,166
Posted By kem1966

I'll take a look at that now and see if I can...

I'll take a look at that now and see if I can notice anything. It would be great if that was all it was. It has been a while since i have done any soldering to terminals, but if that is all it is,...
Replies: 25
Views: 9,166
Posted By kem1966

Good evening, My fault for not noticing the...

Good evening,

My fault for not noticing the difference from terminal 1 and C1. I should have looked at it closer. My fault.

But I did do what you had said, and when the volt meter is on C1 and...
Replies: 25
Views: 9,166
Posted By kem1966

Hello again, I got out of work a little...

Hello again,

I got out of work a little early to try this.

I tried your test with a thermostat, turning them up to call for heat, and the same things did happen, about two minutes after turning...
Replies: 25
Views: 9,166
Posted By kem1966

I did try what you said with the wire, and you...

I did try what you said with the wire, and you could hear the relay click, the boiler fired up, but the circulator pump did not kick in. I held the wire in place again on a different valve and the...
Replies: 25
Views: 9,166
Posted By kem1966

Oh ya, I did feel the valves and two of them...

Oh ya,

I did feel the valves and two of them where very very warm, 1st floor and 2nd floor. The basement valve was just barely warm, but I dont keep the basement thermostat very high either,...
Replies: 25
Views: 9,166
Posted By kem1966

I will ask someone I know tomorrow. I should be...

I will ask someone I know tomorrow. I should be able to hook up with someone who has one
Replies: 25
Views: 9,166
Posted By kem1966

Hello, The three zone valves that I have are...

Hello,

The three zone valves that I have are the TACO zone valves
Replies: 25
Views: 9,166
Posted By kem1966

I dont have a volt meter, but what I did do was...

I dont have a volt meter, but what I did do was to open each zone by opening the manual switch. I did each zone individually and nothing happened. Then opened all three of them at once, and again,...
Replies: 25
Views: 9,166
Posted By kem1966

I have three zone valves, and one thing I tried...

I have three zone valves, and one thing I tried was to open the valves to let a constant flow of water though them, but when done so, the circulator would not kick in.
Replies: 25
Views: 9,166
Posted By kem1966

Circulator Pump not working all the time when called for

I have been having a problem with the boiler not coming on when the thermostats call for heat. When It first happened I turned the power switch to the boiler off and back on and the circulator pump...
Replies: 4
Views: 8,273
Posted By kem1966

circulator pump not working all the time when called for

I have been having a problem with the boiler not coming on when the thermostats call for heat. When It first happened I turned the power switch to the boiler off and back on and the circulator pump...
Showing results 1 to 18 of 18


 
Forum Jump