Search: Posts Made By: pillot
Showing results 1 to 25 of 35
Search took 0.01 seconds.
Replies: 2
Views: 629
Posted By pillot

Well thee reason I was asking was because I was...

Well thee reason I was asking was because I was not getting enough heat so I raised the setting on the boiler by about 20 degrees to around 190 and wanted to make sure that I didn't set it too high....
Replies: 5
Views: 1,070
Posted By pillot

Not sure where I heard or read this but my...

Not sure where I heard or read this but my understanding is that the slower the water flow through the baseboard the more time the water has to release it's heat, where as the faster the water flow...
Replies: 5
Views: 1,070
Posted By pillot

Question Circulating pump

My circulating pump for each zone has 3 speed settings low, mid, & high. Can someone tell me what is the normal setting, it is currently set to low and was wondering if I should switch it to medium...
Replies: 2
Views: 629
Posted By pillot

Question 4 yr old burnham boiler

Hello,

General question about my boiler, I was checking out the temp guage and notice that it usually reads between 170 - 190, the boiler turns on once it hits below 170 and shuts off when it...
Replies: 8
Views: 2,492
Posted By pillot

Thanks for the responses, but I still don't...

Thanks for the responses, but I still don't understand why having air in the system is a probem when there is an inline air separator (IAS). Wouldn't this take care of any air that manages to get...
Replies: 8
Views: 2,492
Posted By pillot

Thanks Mike, but could you explain what is meant...

Thanks Mike, but could you explain what is meant by "portable water"
Replies: 8
Views: 2,492
Posted By pillot

PEX tubing for heating

Hello,

I purchase a roll of PEX tubing from HomeDepot and need to know if this can be used for heating, so is there anything I should check to be sure that it can be used to connect baseboard...
Replies: 4
Views: 4,370
Posted By pillot

It is not a monoflow loop, basically, it is a...

It is not a monoflow loop, basically, it is a single 3/4" loop which feed the first baseboard then goes out to the next one and so on. I would like to splice into the loop and add this kick toe but...
Replies: 4
Views: 4,370
Posted By pillot

Installing Kick Toe Heater

Hello,

Would like to add a kick toe heater but notice that it's water supply is 1/2" where as my current heating system uses a 3/4" loop. I've been told to use a monoflow tee, would like to know...
Replies: 4
Views: 19,902
Posted By pillot

Thank You Mr Ron, I figuired out my problem and...

Thank You Mr Ron, I figuired out my problem and it was caused by a stample shorting out the red with the yellow wire on the new keypad. Even after correcting this the keypad continue to show keybus...
Replies: 4
Views: 19,902
Posted By pillot

MrRon Initially I thought it was the new...

MrRon

Initially I thought it was the new equiptment so I discounted the new devices and still get a keybus error on my original keypad. The date and time on the keypad need to be reset cause it...
Replies: 4
Views: 19,902
Posted By pillot

Unhappy Keybus Fault error - Help please

I attempted to add a new keypad and zone expander (pc5108) to my DSC PowerSeries 832, I discounted the power/battery and after installing the new hardware I am now getting KEYBUS FAULT error on both...
Replies: 5
Views: 7,351
Posted By pillot

Could someone list the steps needed to program a...

Could someone list the steps needed to program a DSC 832 to page me when the alarm goes off.


Thanks
Replies: 1
Views: 1,614
Posted By pillot

Need a lock for my DSC alarm box

Does anyone know where I can get a lock for my DSC alarm box, I puchased this complete DSC powerseries kit on ebay but the metal housing did not include a lock, so the box will not shut close.
...
Replies: 2
Views: 1,403
Posted By pillot

Best place to mount wireless main panel

Thinking of getting the GE Simon XT wireless, I've read that most common place to put the main control panel is hidden inside a closet to prevent an intruder from tampering with the unit. But would...
06-09-09, 01:53 PM
Replies: 1
Views: 632
Posted By pillot

exhaust vent gap

Hello.

I replaced the exhaust vent for my hot water heater, there is a gap all around the pipe where it goes through the cinder block wall out to my chimney stack, it's a 3" galvanized tube going...
Forum: Water Heaters
06-08-09, 07:20 AM
Replies: 2
Views: 1,175
Posted By pillot

Exhaust vent gap

Hello.

I replaced the exhaust vent for my hot water heater, there is a gap all around the pipe where it goes through the cinder block wall out to my chimney stack. Does any one know what I can ...
Replies: 2
Views: 1,337
Posted By pillot

PC5010 telephone wiring help needed

Hello,

Trying to wire in my telephone line to my 5010 panel, the telephone line has 4 color wires (Red, Green, Black, & yellow), however, the instruction book shows red, green, grey, & brown as...
Replies: 2
Views: 1,365
Posted By pillot

Post removed - got my answer from researching...

Post removed - got my answer from researching other posts within this forum.

Thanks
Replies: 9
Views: 2,670
Posted By pillot

How do I check/adjust the expansion tank? ...

How do I check/adjust the expansion tank?

thanks
Replies: 9
Views: 2,670
Posted By pillot

I am unable to post any picture because I cannot...

I am unable to post any picture because I cannot find the cable to hook up my camera to the PC.
I have been able to locate a user's information manual which was attached to the side of my unit and...
Replies: 9
Views: 2,670
Posted By pillot

OK, Have not been able to upload any pics, but I...

OK, Have not been able to upload any pics, but I did find a control knob refered to as the limit and this is set to 140. Is the set too low? My understanding is that this sets the limit for the...
Replies: 9
Views: 2,670
Posted By pillot

Thanks Guys, will post pics tonight When I get...

Thanks Guys, will post pics tonight When I get home.
Replies: 9
Views: 2,670
Posted By pillot

Is my boiler big enough?

Hello,


I'm having a problem heating my house, all my baseboards are warm but it takes literally hours just get my room temp up a couple of degrees.


Here are my concerns:

1. Do I need a...
Replies: 1
Views: 1,171
Posted By pillot

Never mind, read another thread which suggests...

Never mind, read another thread which suggests setting section 076 option 8 "ON" for autoscroll


Thanks
Showing results 1 to 25 of 35
 


 
Forum Jump