Search: Posts Made By: k301s_first
Showing results 1 to 25 of 38
Search took 0.01 seconds.
Replies: 4
Views: 1,527
Posted By k301s_first

While that plug is out, pour in a little Marvel...

While that plug is out, pour in a little Marvel Mystery Oil or a few squirts of Seafoam Deep Creep, re-install spark plug, and let it soak for a day or two with the piston(spark plug hole) facing up....
Replies: 12
Views: 6,619
Posted By k301s_first

Well gentlemen......... I replaced the switch for...

Well gentlemen......... I replaced the switch for $27 and all is well again!!! Thank you, so much, for the time and attention. It was very much appreciated!!!!!............ ALAN
Replies: 1
Views: 1,491
Posted By k301s_first

Husqvarna YTH 180 woe's ........

Husqvarna YTH 180
Family # SKH624U1G2RB
Model # CV18S
Spec # 61533


I attempted to start this engine today with no luck. First, it started no problem, then died on me very soon afterwards....
Replies: 12
Views: 6,619
Posted By k301s_first

Ok........ For $30 I figured I'd simply replace...

Ok........ For $30 I figured I'd simply replace the switch and HOPE that this takes care of the problem. I'll post back with the results when I get this thing installed and test it. Thanks for the...
Replies: 13
Views: 10,358
Posted By k301s_first

Will do. Thanks...

Will do. Thanks again!!!!...........................ALAN
Replies: 13
Views: 10,358
Posted By k301s_first

Thank you for clearing these questions up. The...

Thank you for clearing these questions up. The can of carb cleaner that I have is the gallon size can with a dipping basket. It was purchased at NAPA for the sole purpose of cleaning the carbs on my...
Replies: 13
Views: 10,358
Posted By k301s_first

1) Ok.....we're good on the tank now. Great!!! ...

1) Ok.....we're good on the tank now. Great!!!

2) Soak the carb overnight in carb cleaner and blow dry with compressed air...... or not?

3) Replace the diaphram with a new one...... or are you...
Replies: 13
Views: 10,358
Posted By k301s_first

Not trying to sound ignorant here, but, years ago...

Not trying to sound ignorant here, but, years ago I was told that you should put something in these metal tanks to aide in the removal of larger particles of rust and what not inside. I was thinking...
Replies: 13
Views: 10,358
Posted By k301s_first

O.K......... I somehow managed to get that darn...

O.K......... I somehow managed to get that darn stem out of there and tilled what was left of the garden. The problem still persists, however, it ins't as frequent as before. It will run for a little...
Replies: 13
Views: 10,358
Posted By k301s_first

Thanks for the much needed info!!! Since posting...

Thanks for the much needed info!!! Since posting the message, I have found that by rapping on the top side of the tank, I could get it to idle fine again after the yo-yo'ing started and the engine...
Replies: 13
Views: 10,358
Posted By k301s_first

Old Model Rototiller Question (Retitled Question)

I have acquired a free tiller at the purchase of my home 2 years ago. Best I can figure, it needs a good carb cleaning. It idles fine for a few minutes and then begins idling up and down constantly...
Replies: 12
Views: 6,619
Posted By k301s_first

Ok........ I disconnected the battery for 30...

Ok........ I disconnected the battery for 30 minutes, reconnected the leads, turned the ignition switch on and off 5 times to reset the computer. Wallah!!! Back to 2WD again. However, I can select...
Replies: 12
Views: 6,619
Posted By k301s_first

2001 S-10 Blazer 4X4 issue......

Hi all. My 2001 s-10 blazer has dropped into low range on the 4X4 electronic switch and will not come out. Anyone here ever had this problem or know how to resolve this issue? Thanks in...
Replies: 5
Views: 1,577
Posted By k301s_first

Yeah....... I'm leaning towards the silicone idea...

Yeah....... I'm leaning towards the silicone idea between the overlapped layers and a nice thick coat of tar on the inside of the structure, at the seams, and crossing my fingers on this. If that...
Replies: 5
Views: 1,577
Posted By k301s_first

The roof is relatively flat from front to back as...

The roof is relatively flat from front to back as best I can tell and, yes, the screws with rubber washers were used during installation. However, the washers are pretty old and brittle. I don't...
Replies: 5
Views: 1,577
Posted By k301s_first

Metal Roof Leaking.....

I have a 30' X 20' metal outbuilding who's roof was pieced together, horrizontally instead of the usuall vertical, with a 15' sheet of metal and a 16' sheet of metal. Where these two pieces are...
Replies: 12
Views: 14,773
Posted By k301s_first

Just wanted to stop back in and say thanks once...

Just wanted to stop back in and say thanks once again. The heater is still doing GREAT!!!!! I have since purchased a service manual on my truck for any and all future repairs needed. THANKS...
Replies: 5
Views: 2,183
Posted By k301s_first

Visit this link for some more helpful...

Visit this link for some more helpful information. I just fixed mine and it didn't cost me a dime to repair it.

http://forum.doityourself.com/showthread.php?p=1119776&posted=1#post1119776

Find...
Replies: 12
Views: 14,773
Posted By k301s_first

What's really upsetting is........ How many...

What's really upsetting is........ How many people has this shop ripped off by actually charging someone $90 for a fifteen minute job that doesn't cost THEM anything to repair? Now, to me, that's...
Replies: 12
Views: 14,773
Posted By k301s_first

HotinOKC........ That was it !!!! I removed both...

HotinOKC........ That was it !!!! I removed both lines to the heater core and filled the hoses with HOT water then, using compressed air, back flushed the core. Then, using the same proceedure,...
Replies: 12
Views: 14,773
Posted By k301s_first

Mattison........ I have a friend that owned a...

Mattison........ I have a friend that owned a 2000 model. He experienced similar problems with his also. Flushing seemed to fix the problem for him as well. And it required flushing every year.

...
Replies: 12
Views: 14,773
Posted By k301s_first

Thanks for the reply Mark. I can hear something...

Thanks for the reply Mark. I can hear something opening and closing, or whatnot, behind the dash when I change the settings on the heater dial. For instance, turning the flow of air to the floor,...
Replies: 12
Views: 14,773
Posted By k301s_first

Thanks Pecos. Yes the radiator is full. I just...

Thanks Pecos. Yes the radiator is full. I just finished flushing the system, with a radiator flush from the parts store, myself and made certain the system was full of fluid. I might consider...
Replies: 12
Views: 14,773
Posted By k301s_first

'01 Chevy S-10 Blazer 4x4...... Little or NO heat!!......HELP!!!

This problem started about 2 months ago. I noticed a gurgling sound from the heater core. Almost like water running into a bucket. Now, I have an intermittent heat problem. I've used an over the...
Replies: 2
Views: 1,184
Posted By k301s_first

No fuel.........carb problem?

The engine in question is a Briggs 14.5 I/C OHV.

Model# 280H07
Type# 0117 E1
Code# 060117 ZD

My problem began when a belt jumped off a pully on my 60" Swisher Finishing Deck. It acted as if...
Showing results 1 to 25 of 38
 


 
Forum Jump