Search: Posts Made By: VengeFulHemi
Showing results 1 to 15 of 15
Search took 0.00 seconds.
Replies: 36
Views: 2,849
Posted By VengeFulHemi

@cheese: A thousand pardons for the delay, tons...

@cheese: A thousand pardons for the delay, tons of bull going on in this house. Dumb*ss me(all my fault) just confused myself because I was looking on briggs website to get an average on in lbs and...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

@mowerdude: Hey buddy, thanks sooo much for that...

@mowerdude: Hey buddy, thanks sooo much for that info. I feel better now.
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Well, ran into two issues today. I tried to...

Well, ran into two issues today. I tried to retorque the bolts and busted the thread and head off of one(luckily lowes had an exact match on them),whewwwww. Then I had to go away for the day, so I...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

What can happen if the bolts are not tight...

What can happen if the bolts are not tight enough? Thanks.
Replies: 36
Views: 2,849
Posted By VengeFulHemi

A shout out to all you thoughtful people who...

A shout out to all you thoughtful people who assisted me to make this repair to my PW. It seems to be working well. Started it up after bolting on the head, adjusted the valves to .05, drained&fill...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

@marbobj: All I was doing was slowly backing out...

@marbobj: All I was doing was slowly backing out the plug and it started off fine, then snagged all of a sudden, then tried to slowly reseat it and started to bind up on me. Then that was the demise...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Ok, I recieved the cylinder, put the internals...

Ok, I recieved the cylinder, put the internals back together, and are awaiting head gasket and cover gasket. Now here is the next issue: I need the valve clearence specs and generac does not provide...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Got the new cylinder head today. One thing I...

Got the new cylinder head today. One thing I can't figure out is which is the exhaust and intake valve and then their proper positioning? I have the pdf for the PW, but it's too large for the upload....
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Hey guys, here is an update: On 5/23 I had...

Hey guys, here is an update: On 5/23 I had ordered a cylinder head from "Jacks Small Engines". When ordered that day, the rep on the phone said that they would have the parts in their warehouse to...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Well, I will be buying the head. I actually took...

Well, I will be buying the head. I actually took the head off and the all the internals. It seems fairly easy. There is alot of carbon buildup all around. Should I address that, and how do I remove...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

@geogrubb: Thanks for the info. I was only just...

@geogrubb: Thanks for the info. I was only just using the pw last week, so the pump is fine. I had no idea that putting on the head involves so much. I thought it was set it and forget it. Do you...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

I was under the thought that it would cost in the...

I was under the thought that it would cost in the range of 90-100. 45 isn't so bad.
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Motor is a "Generac OHC 196cc"

Motor is a "Generac OHC 196cc"
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Thank you very much Gunguy45 for getting back to...

Thank you very much Gunguy45 for getting back to me so quickly and for the help. I looked at YT videos on what you suggested and looks somewhat simple. But i'm afraid of one thing, the surface of the...
Replies: 36
Views: 2,849
Posted By VengeFulHemi

Replace Cylinder Head

Hi Everyone:
Glad to be part of this community. I have a dillemma. Stupid me was trying to remove the spark plug from my pressure washer and I stripped the hole:wall:. Hopefully someone can...
Showing results 1 to 15 of 15


 
Forum Jump