Search: Posts Made By: ko49028
Showing results 1 to 14 of 14
Search took 0.01 seconds.
07-01-13, 08:14 AM
Replies: 3
Views: 2,893
Posted By ko49028

Solution... I was able to locate a new motor,...

Solution... I was able to locate a new motor, 4681A20040G, on eBay for about $40. Apparently, the last letter is the revision. Repair complete. Thanks.
06-20-13, 09:16 AM
Replies: 3
Views: 2,893
Posted By ko49028

Goldstar WD3010 fan motor replacement

I have a Goldstar WD3010 Dehumidifier. The fan motor(p/n 4681A20040C) does not work. I have jumped the motor's thermal protector and tried it to verify a problem; this trips the circuit breaker. I...
Replies: 10
Views: 9,729
Posted By ko49028

With the top off, drum reinstalled, and dryer...

With the top off, drum reinstalled, and dryer running, I attempted to check some voltages. However, one of the leads slipped from my hand and contacted two adjacent terminals... the drum spinning...
Replies: 10
Views: 9,729
Posted By ko49028

The dryer is on a circuit breaker. There are 240...

The dryer is on a circuit breaker. There are 240 volts at the recepticle. I removed the drum to inspect the elements; continuity checks out on them. There is a limit switch that I tested and had...
Replies: 10
Views: 9,729
Posted By ko49028

GE Dryer not heating/drying

I have a General Electric Clothes Dryer (Model # DDE7230LDLWH; serial # LL209795G) that has just quit functioning properly. The drum still spins, and the timer seems to function. Air still passes...
Replies: 5
Views: 3,969
Posted By ko49028

To finish out this thread... indypower1 had it...

To finish out this thread... indypower1 had it pegged. I thoroughly cleaned the carb and changed the oil. However, much to my surprise, I removed one of the shrouds that practically hugged the...
Replies: 5
Views: 3,969
Posted By ko49028

For clarification, when I was running it and it...

For clarification, when I was running it and it quit, none of the drive systems were engaged. The oil level was fine. The oil does appear to be fairly black, but not thick.
Replies: 5
Views: 3,969
Posted By ko49028

Snowblower engine seizing up

I have acquired a Simplicity 755 snow blower with electric start with a Tecumseh engine. I apologize for no other numbers as it was repainted. Based on an online manual, I believe the engine is: ...
Replies: 2
Views: 1,508
Posted By ko49028

Question Any Stanley gurus have any info? Any hints...

Any Stanley gurus have any info?

Any hints on what I should be looking for relative to the "up limit" when I tear into the unit?
Replies: 2
Views: 1,508
Posted By ko49028

Garage Door Opener Won't Shut Off

I have a Stanley Quiet Glide (Chain Drive) SecureCode, model #ST605. I purchased it in 2001. The lifetime warranty is pretty useless with the manufacturer out of business.

After a couple...
01-05-08, 05:45 PM
Replies: 8
Views: 2,720
Posted By ko49028

Thumbs up The tapping worked. Thank you. I realize this...

The tapping worked. Thank you. I realize this may be temporary. Any idea on what a replacement would/should cost.

I tip my hat to this site. This is probably my 4th or 5th fix in my house.
01-05-08, 02:41 PM
Replies: 8
Views: 2,720
Posted By ko49028

The control board has the following printed on...

The control board has the following printed on it:

The General 90
Inter City Products
Total Furnace Control
Model 50A50-110

Also, printed to the side is: 1380-686

Any help would be...
12-18-07, 09:08 PM
Replies: 8
Views: 1,339
Posted By ko49028

I have had this problem on a couple different...

I have had this problem on a couple different occasions with a couple of different causes and solutions.

1st time turned out to be the limit switch (trips when the heat in the plenum gets too...
12-18-07, 06:59 PM
Replies: 8
Views: 2,720
Posted By ko49028

Glow Ignitor stays on

I have an Arcoaire RPJ II gas forced air furnace. The glow ignitor remains on all the time. I have only recently noticed it. There are no flashing code indicators. It is on throughout the entire...
Showing results 1 to 14 of 14


 
Forum Jump