Search: Posts Made By: ithinkicandoit
Showing results 1 to 25 of 65
Search took 0.01 seconds.
03-25-13, 02:18 PM
Replies: 6
Views: 766
Posted By ithinkicandoit

I have gone through all of the outlets and moved...

I have gone through all of the outlets and moved backstabs to screws from the point that I am having trouble to the end of the line. Same problem remains... Power to half the room leading up to the...
03-16-13, 04:40 PM
Replies: 6
Views: 766
Posted By ithinkicandoit

thanks Ray, I will follow this guide. One...

thanks Ray, I will follow this guide. One question, I have an outlet that transitions to a new outlet I created to power under my desk to run my computer. This outlet is also one that is linked to a...
03-16-13, 04:13 PM
Replies: 6
Views: 766
Posted By ithinkicandoit

problem on a line

Out of nowhere, one of my circuit lines is having a problem. Woke up the other morning to the power in my study being out. Flipped the breaker, but it didn't help. I assumed my breaker was no good,...
01-09-13, 07:34 PM
Replies: 7
Views: 7,811
Posted By ithinkicandoit

7723 So you are saying I need to increase my...

7723

So you are saying I need to increase my pressure into the line? I didn't want to go too high for fear of blowing out something that I shouldn't. (I finally got to adding a picture...)
12-02-12, 08:17 AM
Replies: 7
Views: 7,811
Posted By ithinkicandoit

it is a 26 gallon tank with 6.1 scfm at 40psi and...

it is a 26 gallon tank with 6.1 scfm at 40psi and 4.3 scfm at 90psi. I have used this compressor to blow out the system last year, with no problems. The "gurgling" is not from water nor is it in the...
12-01-12, 11:54 PM
Replies: 7
Views: 7,811
Posted By ithinkicandoit

sprinkler system blow out problem

I was blowing out my sprinkler system, using only 40 lbs of pressure. The first 2 zones blew out fine, but then I heard a gurgling sound coming from the piping near where I attached the air hose. The...
11-24-12, 02:54 PM
Replies: 2
Views: 1,142
Posted By ithinkicandoit

Any recommendations on what to buy? My basement...

Any recommendations on what to buy? My basement is unfinished, but we do use it for the kids to play in. It is approximately1500 sq ft. I guess a comparable unit... I was looking at the Danby...
11-24-12, 01:42 PM
Replies: 2
Views: 1,142
Posted By ithinkicandoit

Whirlpool AD65USM2 tripping breaker

I have owned and operated successfully, a Whirlpool AD65USM2 for the past 7 years. Recently, it started to trip my circuit breaker. There are no other new electrical devices being run off of this...
11-15-12, 10:04 AM
Replies: 1
Views: 1,104
Posted By ithinkicandoit

unmodified thinset

I am installing travertine tile over ditra using unmodified thinset. How long before I can walk on it? Then, how long before I can move my refrigerator back in place? (I am thinking 24 and 48?) or...
11-13-12, 01:29 PM
Replies: 4
Views: 5,127
Posted By ithinkicandoit

Nevermind, just read up on sanded vs. unsanded......

Nevermind, just read up on sanded vs. unsanded... I guess I need to make larger spaces, or switch to unsanded grout...
11-13-12, 01:20 PM
Replies: 4
Views: 5,127
Posted By ithinkicandoit

So, I am using 1/8" spacing, so the grout lines...

So, I am using 1/8" spacing, so the grout lines are pretty thin to begin with. I think I am resigned to using the spacers as a guide, and eyeballing/adjusting as I go... I bought sanded grout... can...
11-13-12, 11:55 AM
Replies: 4
Views: 5,127
Posted By ithinkicandoit

french pattern layout problem

I am getting ready to lay my travertine tile in a french pattern. The tile came pre-packaged with exact sizes to create the french pattern. The problem I have is they are exactly the same size, just...
09-16-12, 09:23 AM
Replies: 9
Views: 2,364
Posted By ithinkicandoit

From what I can see, they are made by LP Building...

From what I can see, they are made by LP Building Products. They are "solid start engineered I joists" 11 7/8" deep and spaced 13 1/2" apart from each other. They have the number 476 stamped...
09-16-12, 08:40 AM
Replies: 9
Views: 2,364
Posted By ithinkicandoit

Not sure how to tell you the details on the...

Not sure how to tell you the details on the joists. There are the main steel beams that run cross of the wood beams. Then there are several stronger looking beams that are layered solid wood but most...
09-16-12, 12:33 AM
Replies: 9
Views: 2,364
Posted By ithinkicandoit

By the way... I notice in my basement the builder...

By the way... I notice in my basement the builder must have layed my subfloor incorrectly. I see printed "this side up" when I look up in my basement, and I have all the knots on the top. Not sure...
09-16-12, 12:30 AM
Replies: 9
Views: 2,364
Posted By ithinkicandoit

knots in subfloor

I just took up my laminate and luan to lay down Ditra under travertine in my kitchen. My plywood subfloor has several knots from the pine which make the floor not completely smooth. Also there are a...
09-09-12, 11:49 AM
Replies: 2
Views: 1,547
Posted By ithinkicandoit

thin plywood underneath laminate

I am pulling up my laminate flooring to install ditra under travertine. Subfloor is plywood. Should I pull up the thin layer of plywood the previous installer put under the laminate or just put the...
Replies: 12
Views: 22,493
Posted By ithinkicandoit

So, if all the connections are tight, do you...

So, if all the connections are tight, do you recommend replacing the unit? And if so, can I "simply" replace the unit, and not all of the chains, etc.?
Replies: 12
Views: 22,493
Posted By ithinkicandoit

Will try that. The light does come on and does...

Will try that. The light does come on and does stay on when the door stops.
Replies: 12
Views: 22,493
Posted By ithinkicandoit

Sorry about that. The door is currently...

Sorry about that. The door is currently disengaged, and I am operating manually. No obstruction with the movement of the door itself. When the door stops, there is no blinking/flashing of the light...
Replies: 12
Views: 22,493
Posted By ithinkicandoit

Model #: 139.53985 Chain opener. ...

Model #: 139.53985

Chain opener.

Sensors are not moved, but the light does not seem to click on when walking through.

It just stops. No reverse.
Replies: 12
Views: 22,493
Posted By ithinkicandoit

craftsman door works intermittently

My Craftsman 1/2 HP garage door opener is working correctly at times, and other times, is only opening/closing partly then stops. You have to keep hitting the button to keep it moving and sometimes...
Replies: 2
Views: 1,437
Posted By ithinkicandoit

Not a Kreg jig

I bought a Silverlight jig at a woodworking show a long time ago, that is similar to a Kreg jig. Does the same thing.... Sort of. When I put in the screw, I am left with the screw head just slightly...
Replies: 3
Views: 1,044
Posted By ithinkicandoit

gaps in mitered frame

I am making a large frame for a mirror project. A couple of the mitered joints aren't completely tight and I have a small gap to fix. Any advice? Should I put woodfiller in the gap, sand, stain? Any...
Replies: 1
Views: 1,904
Posted By ithinkicandoit

Delta table saw insert

I have a 10" Delta Table Saw (model 36-650). I just bought an 8" Freud dado blade stack set and wanted to test it out. My insert has been sticking, and this time it wasn't budging. I had to pop it...
Showing results 1 to 25 of 65
 


 
Forum Jump