Search: Posts Made By: Nathand
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 2
Views: 1,712
Posted By Nathand

Exclamation Mortar bed question/shower pan install

Hi All,

Tha shower pan in my house has always rocked a little when you are in it. This causes the bead of calking to rip loose frequently. I finally decided to fix it this weekend and here is...
Forum: Water Heaters
03-24-08, 08:49 PM
Replies: 6
Views: 9,182
Posted By Nathand

Has anyone ever had to clean the elements? I...

Has anyone ever had to clean the elements? I want to pull them out and see how they look but I don't want to find out that there is some seal that I can't reuse. Do they get covered with scale?
...
Forum: Water Heaters
03-24-08, 04:21 PM
Replies: 6
Views: 9,182
Posted By Nathand

Another thing I did not expect was that the lower...

Another thing I did not expect was that the lower element was hot at 240V but the top was dead. Is it set up backwards?

Thanks,

Nathan
Forum: Water Heaters
03-24-08, 04:10 PM
Replies: 6
Views: 9,182
Posted By Nathand

Well, I checked the elements and they both came...

Well, I checked the elements and they both came in between 12 and 13 ohms. I was hoping for the bottom one to be way different. As for checking the thermostat, how does one do that? What would I...
Forum: Water Heaters
03-24-08, 01:10 PM
Replies: 6
Views: 9,182
Posted By Nathand

GE hot water heater.

Hi, I have a GE hot water heater and the water comes out plenty hot and plenty of it for the first shower and a half. Then it tapers off quickly. It didn't used to do this. There are 2 heater...
Replies: 1
Views: 816
Posted By Nathand

Engine wiring

Well, I made a swap last night from the 12HP BS single in my wards rider to a 17HP Briggs twin. It fit right up stack pulley and all. As for the wiring, the yellow from the armature looks to be the...
Replies: 11
Views: 18,094
Posted By Nathand

Sure would be helpful to have bolt pattern info...

Sure would be helpful to have bolt pattern info for both motors. The I could make a drill template. I work in metal fab so I am prepared to do some modifications. Do you know of a link to BS...
Replies: 11
Views: 18,094
Posted By Nathand

I have thought about that and may look into that...

I have thought about that and may look into that but I do really like the wards mower. It is fast and easy to operate just shy on power in deep grass. It is also in better shape that the newer...
Replies: 11
Views: 18,094
Posted By Nathand

I replaced the belt when I adopted the mower. ...

I replaced the belt when I adopted the mower. The idlers look and feel good as well. I split the cases on the trans about an hour ago. It has some really silvery looking oil in it. I suspect a...
Replies: 11
Views: 18,094
Posted By Nathand

Well, I guess I am not sure if it is a VST. The...

Well, I guess I am not sure if it is a VST. The model just says 205-024C.
Replies: 11
Views: 18,094
Posted By Nathand

I'll check the model # of the trans tonight after...

I'll check the model # of the trans tonight after work. It is a VST. I had the manual you posted a link for and unfortunately there is little or no helpful repair info in there. In general, can...
Replies: 11
Views: 18,094
Posted By Nathand

Peerless Hydrostatic Transmission

Hi there,

I adopted a murray rider with a 17HP Briggs twin and a peerless hydrostatic transaxle. It runs great but drives impossibly slow. I pulled the transaxle out and looked in the little...
Replies: 2
Views: 715
Posted By Nathand

Riding Mower Question

I have a general Riding mower question, The front beam on the two mowers I have that contains the steering spindles, etc, appear to pivot around the center. Are they supposed to be locked down...
Showing results 1 to 13 of 13


 
Forum Jump