Search: Posts Made By: wareagle
Showing results 1 to 25 of 133
Search took 0.02 seconds.
11-03-13, 06:18 PM
Replies: 1
Views: 678
Posted By wareagle

Help with central heating

I have a gas central unit. I lit the pilot and then turned the gas to the heater on.
When I lowered the temp on the thermostat, the fan came on along with the fire at the burner. It was on about 5...
06-16-12, 02:33 PM
Replies: 8
Views: 3,305
Posted By wareagle

Check here GEC Machines GEC Machines Questions...

Check here GEC Machines
GEC Machines Questions & Answers (http://www.scribd.com/doc/16241903/GEC-Machines-Questions-Answers)
05-31-12, 01:39 PM
Replies: 12
Views: 1,634
Posted By wareagle

Under Questions 1. Yes Need name plate amps ...

Under Questions
1. Yes Need name plate amps
2. Yes Need name plate amps
3. I don't know. You need to post the actual amperage on the equipment name plate.

Ray I would not call that a service...
04-29-12, 01:55 PM
Replies: 14
Views: 1,408
Posted By wareagle

Ir = V/R Ic = V/Xc<-90 Il = V/Xl <90 ...

Ir = V/R
Ic = V/Xc<-90
Il = V/Xl <90

Ieq = Ir + Ic + Il which is vector addition for the total amps
03-14-12, 12:58 PM
Replies: 2
Views: 1,049
Posted By wareagle

That could be the case. Splices some times do...

That could be the case. Splices some times do that. The fault generated was not great enough to cause the overcurrent device to take the line out of service. This happens if the impedance of the...
03-09-12, 07:20 PM
Replies: 1
Views: 1,110
Posted By wareagle

It is the primary system neutral.

It is the primary system neutral.
01-29-12, 04:20 PM
Replies: 17
Views: 1,783
Posted By wareagle

one more time. What is the voltage and wattage of...

one more time. What is the voltage and wattage of the heaters?
01-29-12, 03:10 PM
Replies: 11
Views: 1,809
Posted By wareagle

Greg and Ray Let say he did have the conductors...

Greg and Ray
Let say he did have the conductors reversed. How does the pilot light have a current path so that it is on? I am not that familar with this switch. I would assume there is not...
01-29-12, 02:57 PM
Replies: 7
Views: 2,686
Posted By wareagle

I believe the new code requires the bath to be on...

I believe the new code requires the bath to be on a separate circuit. That means nothing else but the bathroom alone is on the ckt. Correct me if I am incorrect.
01-29-12, 02:51 PM
Replies: 17
Views: 1,783
Posted By wareagle

The first major sin was to connect a 15 amp...

The first major sin was to connect a 15 amp conductor(#14) to a 20 amp breaker. Major violation.
You need to provide the voltage and wattage of the heaters. Most of the information seems to have...
01-17-12, 10:23 AM
Replies: 15
Views: 1,514
Posted By wareagle

add a 240/120 volt transformer at the end. Lot...

add a 240/120 volt transformer at the end. Lot cheaper that the big wire.
01-16-12, 08:21 PM
Replies: 15
Views: 1,514
Posted By wareagle

240 volts #10 cu #8 AL VD 2+%

240 volts #10 cu #8 AL VD 2+%
01-08-12, 04:06 PM
Replies: 24
Views: 7,199
Posted By wareagle

Post Quote"The wire in question is the feeder wire...

Quote"The wire in question is the feeder wire from a new meter box with a 100A circuit breaker only and the Sub-panel is located inside the house protected also with a 100A ciricuit bereaker. I am...
01-08-12, 03:51 PM
Replies: 8
Views: 1,384
Posted By wareagle

Your questions are very basic information that a...

Your questions are very basic information that a qualified electrician would know. Do you self a favor and get someone who knows what they are doing. You may burn the whole place down.
01-03-12, 12:06 PM
Replies: 2
Views: 879
Posted By wareagle

What so you mean by pre-wired connections? The...

What so you mean by pre-wired connections? The generator is normally installed close to the electric meter along with a transfer switch.
01-03-12, 11:57 AM
Replies: 8
Views: 10,040
Posted By wareagle

Not if you are using 120 volts. 12, 24 v is...

Not if you are using 120 volts. 12, 24 v is OK.....
01-03-12, 11:52 AM
Replies: 14
Views: 1,343
Posted By wareagle

You said you have 3 cables. One is the 120 volt...

You said you have 3 cables. One is the 120 volt source and the other two go to the disposal and light. Determine with your voltmeter which cable is "hot". The black wire will go to the top of one...
01-03-12, 11:35 AM
Replies: 6
Views: 1,719
Posted By wareagle

Switch may be just making continuity. If you do...

Switch may be just making continuity. If you do not want it, I would remove the 3 wires from the switch, making note of where they are connected. Check an see if your light still works with
A & B....
01-21-08, 03:42 PM
Replies: 14
Views: 1,167
Posted By wareagle

The code does not prevent you from using a 20 amp...

The code does not prevent you from using a 20 amp rec. on a 15 amps ckt. The 15 amp breaker will protect the wiring from overload. If you use a standard rec, each plug is rated 15 amps.
01-06-08, 06:15 PM
Replies: 3
Views: 1,306
Posted By wareagle

1. If the GFI tripped you would not be able to...

1. If the GFI tripped you would not be able to open your door. Thats the only reason I can think of now.
2. I see no reason. What are you going to connect to this circuit?
Replies: 6
Views: 1,051
Posted By wareagle

I tried what you suggested but no change. I did...

I tried what you suggested but no change. I did try to run the program. I ran hpqthb08.exe but got the same results.
Guys,thanks for you suggestions.
Replies: 6
Views: 1,051
Posted By wareagle

Rick I check and the file is in that folder....

Rick
I check and the file is in that folder. However it may be
corrupt.
Replies: 11
Views: 1,034
Posted By wareagle

I'm getting nothing from this site. Also I am...

I'm getting nothing from this site. Also I am looking to convert old 8mm to dvd or vcr tapes.
Replies: 6
Views: 1,051
Posted By wareagle

Home Computer Problem

When I boot up I receive this message "Fail to Load Library
MSCORLIB.dll". The file is available on the hard drive. The program package is "C:\Program Files\Hewlett-Packard\Digital...
11-23-07, 10:13 PM
Replies: 39
Views: 1,421
Posted By wareagle

The reason you have not heard anyone doing this...

The reason you have not heard anyone doing this is because it probably wont work. One reason is because to parallel #12 is a code violation. Another is that you will get about an 80 volt drop when...
Showing results 1 to 25 of 133
 


 
Forum Jump