Search: Posts Made By: six50joe
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 3
Views: 1,199
Posted By six50joe

Thanks. I wasn't sure if the 2 keypads were...

Thanks. I wasn't sure if the 2 keypads were wired or not, but either way- would you recommend against disconnecting power to the control module, prior to doing anything with the keypads?
01-29-18, 04:27 AM
Replies: 9
Views: 4,288
Posted By six50joe

When connected to the broiler terminal (white...

When connected to the broiler terminal (white wire), the bake igniter works.- would seem conclusive that it's the spark board. I ordered a replacement. Thanks Pjmax for your suggestions!
01-27-18, 04:16 PM
Replies: 9
Views: 4,288
Posted By six50joe

The spark module is one of the 3 pics in my...

The spark module is one of the 3 pics in my original post. Is it likely given that I've tried a new igniter and the connection seems good that the module is bad and needs to be replaced?
01-27-18, 05:05 AM
Replies: 9
Views: 4,288
Posted By six50joe

I tried the test of looking for the spark with...

I tried the test of looking for the spark with the lights out. Only the broiler sparker ignites. I inspected closely the wire connection to the lower sparker, which looks good. I'm assuming both...
Replies: 3
Views: 1,199
Posted By six50joe

Replacing Napco GEM-P1632

We purchased a home a year and a half ago that had a GEM-P1632 installed. It has been powered and 'on line' since we moved in, but I'm assuming not connected to a security service provider that the...
01-24-18, 08:42 AM
Replies: 9
Views: 4,288
Posted By six50joe

I appreciate your highlighting the area to...

I appreciate your highlighting the area to inspect, thanks much for that. I will have access to the stove again over the weekend so I will try your recommendation then and give an update.
01-23-18, 06:21 AM
Replies: 9
Views: 4,288
Posted By six50joe

Thanks for responding PJmax. It will be great...

Thanks for responding PJmax. It will be great if fixing my issue would be as simple as clearing a clogged area somewhere near the burner. I just wanted to clarify a couple of things- first, does...
01-22-18, 09:51 AM
Replies: 9
Views: 4,288
Posted By six50joe

Troubleshooting Maytag gas oven igniter

I have a Maytag gas (propane) oven, model MGR7662WS, for which the lower igniter stopped working. Gas flow is not an issue, as the stove top and broilers function properly. Can hear clicking, but...
11-02-16, 06:25 AM
Replies: 2
Views: 8,112
Posted By six50joe

Thanks for your response. Would it be incorrect...

Thanks for your response. Would it be incorrect to rule out the incline motor as the problem, since mechanically incline works correctly, and decline also does (briefly when I run the calibration)?...
11-01-16, 02:18 PM
Replies: 2
Views: 8,112
Posted By six50joe

Fixing Sole F63 Treadmill incline error

Hope this is the appropriate forum to post this question.

We negotiated with the previous owner of our home to leave some fitness equipment behind before we bought our new home last month. Among...
07-27-14, 06:16 PM
Replies: 1
Views: 638
Posted By six50joe

Can something be used in place of gasket in compression fitting?

I have a Laufen bidet, about 30 years old that had been imported from Europe at the time. When the boiler in our house failed a while back, we had some damage to our plumbing when the temperature...
05-01-14, 06:22 AM
Replies: 7
Views: 6,632
Posted By six50joe

Thanks Grady, I have called literally every...

Thanks Grady,
I have called literally every plumber and plumbing company in the area. Every one of them, including the largest and most well known one has said they will not do this type of work. ...
04-30-14, 06:52 AM
Replies: 7
Views: 6,632
Posted By six50joe

Connecting propane to Generac Generator- why so expensive?

I purchased a 14KW Generac standby generator 2 months ago and had an electrician do all the connections from the generator outside to the transfer switch inside and to my main circuit breaker. As...
Showing results 1 to 13 of 13


 
Forum Jump