Search: Posts Made By: cdestuck
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 13
Views: 6,914
Posted By cdestuck

Check to see if you can see gas squirting in the...

Check to see if you can see gas squirting in the carb throat when you push the primer. I don't know what type of primer may be on there but the tube from primer to carb could have a leak or the...
02-13-16, 09:11 PM
Replies: 8
Views: 934
Posted By cdestuck

Key Klamp pieces are very $$$

Key Klamp pieces are very $$$
02-13-16, 07:23 PM
Replies: 9
Views: 1,347
Posted By cdestuck

The highest output pump would be a sewage pump,...

The highest output pump would be a sewage pump, google them. And in the same size pt that you have, I've been able to make a metal stand and place a 2nd pump directly above the lower pump.

I cant...
Replies: 6
Views: 661
Posted By cdestuck

I would use long panel nails and on the back of...

I would use long panel nails and on the back of the board your installing I would put quarter size dots of regular latex caulking here and there. Caulk when dried does make a good adhesive but will...
02-13-16, 06:17 PM
Replies: 2
Views: 595
Posted By cdestuck

Recessed LED round deck lights for in floor.

Looking to do some lighting on my outdoor deck. I have the vinyl decking on my deck. So I want to recess some round LED lights around the perimeter of the deck just inside the railing. The light will...
Replies: 7
Views: 756
Posted By cdestuck

I prob too late but these cost less than 20 bucks...

I prob too late but these cost less than 20 bucks each at lowes. Watch a YouTube and do it yourself or get a friend to do it and give them 50 bucks for the 40 minutes of labor.
Replies: 9
Views: 1,374
Posted By cdestuck

Use your hole saw to drill a hole through a piece...

Use your hole saw to drill a hole through a piece of 3/4" material. With clamps or some manner fasten thisholecentered above the existing hole. 3/4" wood will guide your bit.
01-23-15, 03:55 PM
Replies: 20
Views: 965
Posted By cdestuck

Often to remove old msiled on boxes, I've...

Often to remove old msiled on boxes, I've disconnected wires, took a lg screwdriver and placed it in the box and whacked it with a hammer. Comes free pretty easy.
Replies: 11
Views: 2,293
Posted By cdestuck

I have Taco circulators. My boiler has two zones...

I have Taco circulators. My boiler has two zones however when I had the system installed, I had the firm put in a series of ball valves to allow my system to run off just one thermostat and act as...
Replies: 11
Views: 2,293
Posted By cdestuck

By quit, I mean when the tstat calls for heat I...

By quit, I mean when the tstat calls for heat I get nothing. The green power light on the controller is own but nothing else happens.

I do you know how closed this company is to helping. I...
Replies: 11
Views: 2,293
Posted By cdestuck

Weil-Mclain boiler control help

So I have a WM HE 2. About 20 years old. Well the boiler quit a couple weeks ago and it appeared to be the control. These controls only seem to last 5-6 years or so. So I bought a 1013-200 WM control...
Replies: 3
Views: 2,037
Posted By cdestuck

Cant help ya with you original question but I did...

Cant help ya with you original question but I did just do the same with a tractor trailer wheel. Didn't do a stone finish but instead went to Lowes and bought some 2000 degree temp spray paint and...
Replies: 6
Views: 2,068
Posted By cdestuck

I have your same model and had the same problem....

I have your same model and had the same problem. Toro now has changed the material and offers a lifetime warranty on this part. As one has mentioned, drill a small hole at the end of each crack to...
Showing results 1 to 13 of 13


 
Forum Jump