Search: Posts Made By: MTWallet
Showing results 1 to 11 of 11
Search took 0.01 seconds.
02-20-19, 09:35 AM
Replies: 10
Views: 488
Posted By MTWallet

A functioning system is certainly the greatest...

A functioning system is certainly the greatest benefit! All the speed stuff seems to be in the ECM control cap as the board only has electronic traces that directly connect t'stat signals with the...
02-20-19, 08:10 AM
Replies: 10
Views: 488
Posted By MTWallet

Tested the ECM motor last night with the...

Tested the ECM motor last night with the teqinspect tester and the motor controller is indeed dead. I had purchased the PSC setup just in case, so went ahead and installed that with the relay tied to...
02-19-19, 01:02 PM
Replies: 10
Views: 488
Posted By MTWallet

Thank you for that! It sure never occurred to me...

Thank you for that! It sure never occurred to me that Cust# on my existing motor would have been the part number.
02-19-19, 11:59 AM
Replies: 10
Views: 488
Posted By MTWallet

I think I'm going to write off the ECM motor and...

I think I'm going to write off the ECM motor and just go with a PSC. Should the following parts work for this conversion?

https://www.grainger.com/product/DAYTON-3-4-HP-Direct-Drive-Blower-4M184...
02-19-19, 10:20 AM
Replies: 10
Views: 488
Posted By MTWallet

An ECM motor is used for variable speeds. As...

An ECM motor is used for variable speeds.
As best I can tell the only speeds this unit has ever run at is "high" when the A/C or heat is on, and "low" when it is fan only.

Making a mistake with...
02-19-19, 08:45 AM
Replies: 10
Views: 488
Posted By MTWallet

Goodman heatpump air handler fan dead

Background: System was in heat mode, I thought the condenser unit was short cycling (iI would come on, could hear a hissing kind of noise in the coils and the fan was running. It would run for maybe...
05-17-18, 09:02 PM
Replies: 4
Views: 368
Posted By MTWallet

I believe I will be going with the XHHW to make...

I believe I will be going with the XHHW to make the pull easier. Thanks for the tip.
05-17-18, 11:46 AM
Replies: 4
Views: 368
Posted By MTWallet

Is this right for a 100 amp subpanel in a detached shop?

I previously got information from some fine folks on this forum about this and am finally getting around to putting into action. From that and information on other forums, I think I have everything...
06-28-17, 09:21 AM
Replies: 6
Views: 2,141
Posted By MTWallet

Thank you all for your responses. I will price...

Thank you all for your responses. I will price out the options and go with make sense.
06-22-17, 09:44 AM
Replies: 6
Views: 2,141
Posted By MTWallet

@Zorfdt What I am understanding from those...

@Zorfdt
What I am understanding from those diagrams is, if you have a neutral and ground buss bar in the distribution panel, you bond (if that is the right word) them to their counterparts in the...
06-21-17, 10:42 AM
Replies: 6
Views: 2,141
Posted By MTWallet

Requesting advice for feeder to 100A subpanel

Hoping to get some advice on best choice of feeder wiring to supply a 100A subpanel in a detached shop. My best description of what I want to do follows...

Existing
225A main disconnect box next...
Showing results 1 to 11 of 11


 
Forum Jump