Search: Posts Made By: brianl0646
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 3
Views: 910
Posted By brianl0646

I ran the test program and all the zones were...

I ran the test program and all the zones were accounted for at least I thought though maybe not the motion detector. How do I disable a zone like the motion detector?

Brian
Replies: 3
Views: 910
Posted By brianl0646

Have a code on ademco panel I don't understand

My sister in law has an alarm. She is not having it monitored and has not been arming it. I ran the test sequence on it and all the sensors seem to be working, but I see a fault 05 on the screen. I...
11-27-04, 10:15 AM
Replies: 4
Views: 9,983
Posted By brianl0646

It was installed by an electrician. If there was...

It was installed by an electrician. If there was a big surge or a short wouldn't the 50 amp breaker on the GFCI trip though? Or does that breaker just trip when there is a ground fault? Is there any...
11-26-04, 07:08 PM
Replies: 4
Views: 9,983
Posted By brianl0646

Hot Tub tripping breaker

Recently I keep tripping the hot tub breaker located on my main panel. My Hot tub is wired to a GFI with a 50 amp breaker near the tub, then this is wired to a 50 amp breaker on my main panel. The...
10-25-04, 01:30 PM
Replies: 3
Views: 1,118
Posted By brianl0646

Would you use that instead of 6 mil poly?

Would you use that instead of 6 mil poly?
10-25-04, 12:21 PM
Replies: 3
Views: 1,118
Posted By brianl0646

Instaling backer board and tile on tub enclousure

I apologize if this is redundant, I just wanted to make sure my specific questions are adressed. My tile was leaking around my tub. It was installed on non waterproof sheetrock. The sheetrock was...
Forum: Water Heaters
10-11-04, 02:38 PM
Replies: 4
Views: 10,730
Posted By brianl0646

So would a short 45 degree right into the side of...

So would a short 45 degree right into the side of the chimmney work? The water heater rests against the chimmney. Does the vent need to go straight up for a certain amount of time before you can put...
Forum: Water Heaters
10-11-04, 11:48 AM
Replies: 4
Views: 10,730
Posted By brianl0646

Gas water heater venting question

I need to replace my water heater. It is an electric model 20 years old, not leaking, but I figure I am living on borrowed time. I want to convert to gas. My water heater is behind and to the side of...
Replies: 1
Views: 1,229
Posted By brianl0646

Question on deck finish to match hot tub

I just built a deck using IPE as the decking material. It is surrounding my hot tub. The tub is unfinished cedar. I have not sealed the deck or the tub yet. I was curious if anyone knows of a sealer...
Replies: 4
Views: 2,456
Posted By brianl0646

I have never cleaned one before, so if you do...

I have never cleaned one before, so if you do have advice it would be appreciated.

Brian
Replies: 4
Views: 2,456
Posted By brianl0646

Chimney cleaning

I was going to brush out my chimney. My flue is clay, (re-done about 10 years ago) It is an oval shape 6x14. I bought a 6 inch round chimney brush. It is a tiny bit smaller then the opening, so I...
05-28-03, 08:52 PM
Replies: 4
Views: 3,621
Posted By brianl0646

Thanks for your advice. Is there anything I...

Thanks for your advice. Is there anything I should use besides galvanized for what I am doing? Its sticking up out of the ground with a spigot on it so I want something that is fairly tough and...
05-28-03, 04:38 PM
Replies: 4
Views: 3,621
Posted By brianl0646

Brass fitting on galvinized pipe

I know nothing about plumbing, so excuse me if this is an obvious question. I backed over my water spigot sticking out of the ground with a Bobcat. The pipe bent into the ground. (it was about a foot...
Replies: 1
Views: 907
Posted By brianl0646

Removing backyard fireplace

I have a fireplace in my backyard. It was built in the 60s. It was made entirely of bricks. I would like to remove it. What is the most efficiant way of taking it apart. I would like to save the...
Showing results 1 to 14 of 14


 
Forum Jump