Search: Posts Made By: vulch
Showing results 1 to 25 of 52
Search took 0.01 seconds.
03-26-16, 03:19 PM
Replies: 16
Views: 1,793
Posted By vulch

Hey Pete looks like i solved the problem after a...

Hey Pete looks like i solved the problem after a lot of research i switched the model plug its a small circuit board from my old board to the new board on terminal PL4 on the control board the fan...
03-25-16, 07:48 AM
Replies: 16
Views: 1,793
Posted By vulch

as you can see in the second pic the old board...

as you can see in the second pic the old board the burnt relay i guess that is what caused the initial problem with the igniter staying on ..
03-24-16, 07:37 PM
Replies: 16
Views: 1,793
Posted By vulch

rfcspositovulch's Library | Photobucket...

rfcspositovulch's Library | Photobucket (http://s649.photobucket.com/user/rfcspositovulch/library/)
03-24-16, 07:09 PM
Replies: 16
Views: 1,793
Posted By vulch

http://i649.photobucket.com/albums/uu214/rfcsposit...

http://i649.photobucket.com/albums/uu214/rfcspositovulch/new%20board_zpsxnswlrf3.jpg...
03-24-16, 05:59 PM
Replies: 16
Views: 1,793
Posted By vulch

its labeled VS HSI HI LO from left to right...

its labeled VS HSI HI LO from left to right in your pic...i tried to post pic but can't
03-24-16, 05:36 PM
Replies: 16
Views: 1,793
Posted By vulch

yes there is a plug in that spot with 2 wires...

yes there is a plug in that spot with 2 wires they are in the first 2 holes left to right in pic. the fan does shut off
03-24-16, 05:08 PM
Replies: 16
Views: 1,793
Posted By vulch

the fan does shuts off normally after the...

the fan does shuts off normally after the burners go off
03-24-16, 04:49 PM
Replies: 16
Views: 1,793
Posted By vulch

Hi yes everything works the only issue is that...

Hi yes everything works the only issue is that the fan is on high speed .if i put the old board in the fan runs as it should on low speed .thanks
03-24-16, 05:02 AM
Replies: 16
Views: 1,793
Posted By vulch

bryant evolution control board

Hi i have a issue with a bryant evolution gas furnace original problem was the igniter burnt so had it replaced that fixed the problem but now the igniter would stay on for the heat cycle .the...
Replies: 3
Views: 1,010
Posted By vulch

Thanks for reply it has 165.000 km seams to puff...

Thanks for reply it has 165.000 km seams to puff some smoke at start up so im thinking valve seals. truck must have been a tow vehicle looks like it had a fifth wheel on it didnt notice that before i...
Replies: 3
Views: 1,010
Posted By vulch

compression test 94 dakota

HI I have just done a comp test on my 5.2l just wondering what you think of these # lowest 150 to 165 test done with wide open throttle truck seams to be using oil ..thanks
Replies: 5
Views: 725
Posted By vulch

cell phone software

Hi i was wondering if anyone knows where i can get a program called (phone tools ) its a program that lets you manage files on your cell phone.thanks
Replies: 1
Views: 743
Posted By vulch

94 dak trans leak

HI all i have a 94 dakota 4wd 318 auto trans had transfer case redone rear trans seal was leaking as well. even after x case rebuild dont think they replaced the rear seal .took it back they...
Replies: 4
Views: 913
Posted By vulch

Thanks for replys i did some calling around today...

Thanks for replys i did some calling around today several tire places told me tire size and wear and manafacturer make a differance are they just trying to sell tires ?one more question i thought...
Replies: 4
Views: 913
Posted By vulch

tire size +4wd

HI all just had my transfer case rebuilt.94 dakota 4wd 318 club cab 158.000 kms . the guy at the shop said that the tires may have taken out the t.c because the front are from a differant...
Replies: 8
Views: 1,225
Posted By vulch

tailgate down better gas milage

Hi i all ways heard that leaving the tailgate down improves mpg .was watching a tv truck show they said thats not true .leaving tailgate up can help improve mpg .any one else heard this
Replies: 6
Views: 1,137
Posted By vulch

Your right .like i said crazy question .thanks

Your right .like i said crazy question .thanks
Replies: 6
Views: 1,137
Posted By vulch

my truck dosen,t have locking hubs so i was told...

my truck dosen,t have locking hubs so i was told . the transfer case engages the front drive shaft and the front diff and shafts turn all the time . i think .am i wrong .thanks
Replies: 6
Views: 1,137
Posted By vulch

Crazy Question 4wd

HI i was just thinking 94 dakota 4wd would it be possible or advisable to remove front drive shafts for the summer months to reduce wear on diff and shafts .transfer case.
Replies: 5
Views: 1,386
Posted By vulch

i HAVE HEARD of thinks getting into the gas tanks...

i HAVE HEARD of thinks getting into the gas tanks and blocking fuel flow only at random times. pump sucks object in then when you shut off motor releases object happens over and over may be a long...
Replies: 5
Views: 898
Posted By vulch

Well i tried shifting different ways still grinds...

Well i tried shifting different ways still grinds out of 4 low goes in to 4 lo good just when shifting out of 4 lo i dont think i will really use 4 lo much but just wondering if there is a bigger...
Replies: 5
Views: 898
Posted By vulch

Thanks for reply i have heard that as well...

Thanks for reply i have heard that as well haven,t tried it yet but will. only had the truck for a little while
Replies: 5
Views: 898
Posted By vulch

dakota 4wd problem

Hi all i have a 1994 dakota 4wd slt 318 v8 when i try to shift out of 4 lo it grinds 4h 2h shift ok manual says to put it in N and shift still grinds i was all so told to try park a little better not...
05-30-06, 08:27 PM
Replies: 8
Views: 1,459
Posted By vulch

problem solved..

problem solved..
05-30-06, 06:57 PM
Replies: 8
Views: 1,459
Posted By vulch

before i bought the softner i had the water...

before i bought the softner i had the water tested 65000 grains hardness iron 1.5 i didnt just think i needed a softner..I called the people i bought the unit from they told me to test t.d.s. i...
Showing results 1 to 25 of 52
 


 
Forum Jump